Axles rated for 6,000 to 7,200 pounds usually will have 3 inch diameters. But it is possible for 5,200 pound axles or even 3,500 pound axles to have a 3 inch diameter axle. You could err on the side of caution and say each axle is rated for 3.5K for a total of 7K for the 2 axles combined.
But there should be some information somewhere on the axles that indicate the capacity. There could be a tag that explicitly states the capacity or some numbers that would indicate the model of the axle.... view full answer...
I wish I knew exactly what wire to use to install a brake controller in your 2007 Buick Rendezvous, but I can explain how to help you find it.
You are going to want to use a circuit tester like our part # 3808 and test all of the wires going into your brake pedal switch until you find one that sees 12 volts when the pedal is applied and none when the pedal is released.
I attached an FAQ on brake controller installations for you to check out also.
The brake controller we recommend the... view full answer...
If your 2007 Buick Rendezvous has factory crossbars that run side to side then the SportRack Vista XL Cargo Box, part # SR7018, will fit as long as the crossbars are no larger than 3-3/4 inches in diameter and the center to center spread is 25-7/8, 27-7/8 or 29-7/8 inches.
Anytime you are going to haul cargo on the roof of your 2007 Buick Rendezvous you will want to check the owners manual or with the Buick dealer for what the roof capacity is for your vehicle. The roof capacity will let... view full answer...
You will still be able to use the T-One Vehicle Wiring Harness, # 118383, on your 2007 Buick Rendezvous even though your vehicle has the tow package installed. This harness connects inline with the vehicle tail lights and gets power for the trailer lighting directly from the the taillights. This harness works exactly the same as the tow package wiring once correctly installed, see instructions.
The advantage to using the tow package wiring, # 41405, is that the trailer lighting power is... view full answer...
Your best chance is replacement key # THKEYN2854. The lock on your cargo box is similar if not the same on many older Thule-made cargo boxes so if anything is going to work it will be this key. If the key goes in but does not turn then the issue could actually be that the key is not fully seated. This is common with new keys and old locks and the solution is to simply tap the key in lightly with a mallet. view full answer...
If you look behind the bumper below the driver side tail light and find a triangular plug that is not connected to anything on your 2007 Buick Rendezvous, then you can use the Hopkins Custom Fit Vehicle Wiring, # 41405.I have included a link to the installation details for reference.
If the plug is not there, you will need to use Tow Ready Custom Fit Vehicle Wiring, # 118383. This harness connects behind each of the tail lights. I have included a link to the installation details for this... view full answer...
According to my research, the 2003 Buick Rendezvous cannot be flat towed unless a transmission lube pump has been installed. This would hold true for either the FWD or the AWD model.
We don't carry transmission lube pumps, but you should be able to find one easily by doing a Google search.
The # RM-020 Roadmaster Tracker tow bar you referenced would work, as its 5000 lb capacity is sufficient to tow your Rendezvous. For a base plate, I'd recommend the Roadmaster # 3107-1. This base plate... view full answer...
When it comes to a hitch for your 2006 Buick Rendezvous, I recommend going with the Curt Custom Fit Trailer Hitch Receiver, # 13469. This hitch is economical, has a tongue weight capacity of 350 lbs, and will provide you with a 2 inch receiver opening for towing or hitch mounted accessories.
Check out the Flint Hill Goods Carrier with 48 Inch Long Ramp, # FHG77ZR. While standing next to the carrier you could power the scooter up the ramp onto the platform, fold the ramp and you are ready... view full answer...
Yes you sure can. The correct replacement trailer hitch hardware kit for the trailer hitch receiver on your 2004 Buick Rendezvous is the Replacement Hardware Kit for Trailer Hitches part # RHK. Once you have arrived at the product page for this hardware kit you will need to enter the part number and brand of the trailer hitch receiver you have. I have attached a list of all our trailer hitch receivers confirmed to fit your vehicle for you. view full answer...
I have a Timbren Suspension Enhancement system that is confirmed to fit your 2005 Buick Rendezvous, but the part # TGMRAZT is for the front wheel drive models. You would want the Timbren System part # TGMRREN as this system is confirmed to fit the all wheel drive Rendezvous.
I attached installation instructions for this kit also. view full answer...
Of the 3 Class III 2 inch hitches we have available, two are going to mount the same way. The Draw-Tite hitch, # 75430, and the Curt hitch, # 13469, have a very similar bolt pattern . They both require holes to be drilled.
The other hitch, Draw-Tite part # 75138 does not require drilling, but will be a longer install as you have to remove the plastic rear bumper cover.
Other than the installation process differences, they have the same features. If you are comfortable using a drill, I... view full answer...
The bag measures 59 inches long by 24 inches wide, so I would recommend a 24x60 cargo carrier. It is a soft flexible bag, and will fit most cargo carriers, but you would get the most out of a 24x60 cargo carrier. Our 24x60 cargo carriers will only fit 2 inch hitches, so if you have a 1-1/4 inch hitch, you would have to use a smaller carrier and bag or replace the hitch with a 2 inch version.
I personally have Tow Ready part # 63153 with the optional tail light kit part # 20174 and it works... view full answer...
The best spot to install the transmission cooler is in front of the radiator, where it will get maximum air flow. If necessary it can be mounted behind the radiator, if there is sufficient clearance for installation.
Installing the cooler in front of your radiator would almost certainly involve removing the grille and possibly the front fascia under the bumper to improve access.
We have an installation video showing a cooler being installed on a different vehicle, watching the video... view full answer...
All of the hitches we carry, Class II and Class III, for the 2005 Buick Rendezvous (see link) state that they will fit the 2 wheel drive and the all wheel drive models. The tongue weight varies only between the Class II and Class III models, with the Class II models showing 300 pounds tongue weight capacity and the Class III models showing 350 pounds tongue weight capacity.
The hitch can be installed on your front wheel drive vehicle and will not affect the rear suspension as long as you... view full answer...
The tow package on your vehicle does not utilize a plug, you do not need one. The tow package wires are located under the dash, and can be accessed by removing the two screws that hold the trim piece on the bottom edge of the dashboard. Gently lower this trim piece, and you will be able to see the 4 blunt cut wires taped to the main wiring harness on the left. There will be black wire, which would attach to the white wire on the controller, a dark blue wire which attaches to the blue controller... view full answer...
The Rightline cargo bag # RL100S20 will fit on a vehicle with or without a roof rack of any kind so it will fit your 2005 Buick Rendezvous. Current pricing for it and for the protective pad # RL100650 are available on their respective product pages and below.
Using a wheel step, # HE4040, will make loading/unloading the bag easier. And if you wish to lock the bag you can use Rightline lock # RL100640. I have included some video and instruction links for you. Be sure to consult the owners... view full answer...
The 3000 lb rating for the Timbren Suspension Enhancement System refers to any load carried in the cargo area of the vehicle and applied to the rear axle, not the towing capacity. The only effect that towing would have on the Timbren system would be any tongue weight exerted on the vehicle by the trailer. The tongue weight (or downward force exerted on the trailer ball) would typically be 10 to 15 percent of the weight of the trailer plus the weight of anything loaded on it.
If you are... view full answer...
The 32x48 inch Reese # PS10401-10402 carrier would work for you, but at around 100 lbs, it'd be pretty difficult for one person or even maybe two to wrangle into place. I'd recommend using a lighter carrier such as the Flint Hill Goods # FHG77ZR. The carrier is around 80 lbs, so it's considerably lighter and its inside platform dimension of 48 x 28 would accommodate your mobility chair perfectly. The carrier is compatible with the 2-inch receiver found on a Class III hitch.
I've linked... view full answer...
As long as the loaded and ready to tow tongue weight of your camper plus the weight of your bikes remains under 350 lbs, then you will have no problem towing your pop up camper with the Swagman Original Towing Bike Rack, # S64675. I have attached an FAQ on how to determine your tongue weight for you to check out.
This bike rack does not include a hitch ball, if you need a 1-7/8 inch hitch ball, then I recommend using the Convert-A-Ball Interchangeable Ball Set, # 802B. If you only need... view full answer...
The only roof rack that can be transferred from your 2005 Buick Rendezvous to a different vehicle is one that uses vacuum cups to attach, the SeaSucker Monkey Bars Roof Rack # 298-SX6000B.
Otherwise, roof racks are specific to each vehicle, so if you wanted a custom fit rack, the only option for your '05 Rendezvous is the following from Yakima:
- Yakima JetStream Crossbars # Y00426
- SkyLine Towers # Y53TR
- Landing Pad 1 # Y00221 view full answer...
Go To Results