I am not aware of that restriction either but I can say that if Yakima (the source) says it's for sure not a thing then you can use anchor mode with the Yakima FullBack # Y02634 and it would have the full 70 lb capacity. view full answer...
We don't have any hitches that fit the Plug In Hybrid versions of the 2021 Hyunda Ioniq but I do have a way you could carry a bike rack. You'd need to go with a trunk mounted bike rack like the Yakima FullBack part # Y02634. This is a nicer trunk rack that is lighter weight, easier to install, and has locks for the rack and for bikes to the rack. view full answer...
Draw-Tite trailer hitch # 24963 weighs all of 20 pounds. The Saris SuperClamp EX # SA4025F weighs 35 pounds. So you could place 55 pounds in your 2018 Hyundai Ioniq's storage area and see if that affects mileage. I believe that it would have a minimal impact if it is even measurable in the short term.
The only other option for carrying bikes with this vehicle would be a roof rack and that will definitely affect the mileage.
There are lighter bike racks you could use. The Neo2, # B01748,... view full answer...
In order to carry electric bikes on a 2021 Hyundai Ioniq you'll need the Curt Trailer Hitch Receiver part # C11486 and Thule EasyFold XT Bike Rack part # TH903202.Typically, you need a larger vehicle to carry electric bikes. That said, this can still be done on a 2021 Hyundai Ioniq but you don't really have many options and due to the rack's design and compatibility, they are not cost effective. The Easy Fold is one of the very few bike racks which can be used with e-bikes and is class... view full answer...
If you're able to remove enough weight from the bike to get it below 35 lbs, I think the # S64650 Swagman XC you referred to would work capably for you. The extra precautions and straps you mention would be an excellent idea.
However, looking at things from a long-run perspective, this rack might not be the best choice for you, even though it's at an attractive price point. The XC isn't the first rack I'd recommend for long trips or frequent moderate trips. It's best use is for occasional... view full answer...
Since your hitch receiver pin hole is about 5" from the back of the bumper on your 2019 Hyundai Ioniq and the RockyMounts MonoRail Bike Rack # RKY10003 is about 5-3/4" from the hitch pin hole in the folded position, it will work but you won't have much clearance.
I recommend going with the other bike rack that you mentioned, the Kuat Sherpa 2.0 2 Bike Platform Rack # SH12G. This rack measures 7-1/2" from the hitch pin hole and will provide extra clearance so that you will not have to... view full answer...
None of the custom fit hitches like the # C11486 are able to fit the PHEV model of the 2022 Hyundai Ioniq. If you really want a hitch you can take the # E17 to a custom fabricator and have them fashion a hitch for your vehicle. If you were planning to use the hitch for a bike rack and don't want to have a hitch made, you could use a trunk mount bike rack like the # Y02634 for 2 bikes or # Y02633 for 3 bikes instead. view full answer...
I have another option for you to carry your bikes, but unfortunately there is not a trailer hitch receiver confirmed to fit your 2019 Hyundai Ioniq EV due to the differences in the rear of the vehicle to accommodate the batteries.
Instead I recommend taking a look at the Yakima FullBack 3 Bike Rack - Trunk Mount - Adjustable Arms # Y02633 which is a confirmed fit for your Ioniq and will allow you to transport 3 bikes weighing up to 35lbs, but no more than a combined weight of 90lbs.
I... view full answer...
Yes, the WeatherTech Universal Cargo Mat # WT11AVMCB that you referenced is made right here in the USA (Chicago, Illinois to be exact). This durable black mat is confirmed to fit in your 2019 Hyundai Ioniq as well. view full answer...
The Curt # C56233 T-Connector you'd asked about is indeed a fit for your 2017 Hyundai Ioniq Hybrid Blue model. The installation is pretty straightforward.
The converter box plugs inline at the connection points between the driver's and passenger taillight wiring harness and the taillight assemblies, and one ground wire needs to be connected to the vehicle body.
You'll also need to run one wire through an existing grommet (usually found under the spare tire) under the vehicle to the... view full answer...
Thanks for reaching out!
To install the Curt T-Connector Vehicle Wiring Harness # C56233 on your 2018 Hyundai Ioniq Hybrid Blue you'll need to use the instructions because as of right now (February 2023) we haven't had the chance to install this on the Blue model.
The instructions are linked to this answer page as well as a photo of the steps needed to take for you to reference. view full answer...
I reached out to my contact at Curt and for your 2017 Hyundai Ioniq using wiring harness # C56381, you will connect that 12V power wire for the harness to the lithium ion starter battery under the back seat on driver's side. It is a little difficult to discern because it is part of the same housing as the larger battery, but this is a separate charging battery specifically for the starter but this is where you will connect your harness. view full answer...
The Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # C56381 requires power directly from the battery. You will need to run that power wire away from hot or moving parts up to your vehicle battery. To do so, there are 3 common methods. I've attached an article to assist with the routing of that power wire with information to help with each one for you to determine the best fit for your vehicle. view full answer...
The Draw-Tite Hitch item # 24963 comes with four M10 X 1.25 X 30 CL10.9 bolts. The best way to prep the weldnuts on your 2018 Hyundai Ioniq is to clean them out with a wire brush.
I have linked an installation video below that we did on a 2018 Ioniq last year that will show you the entire process. view full answer...
The best option for a hitch would be the Draw Tite # 24963 which is a confirmed fit and will work well. I prefer this over the Curt equivalent as it does not require a stabilizer strap when carrying a non-supported load like a bike rack.
I really like the Saris Freedom Superclamp part # SA4025F. This is a lightweight platform rack (which is normally an unheard of combo). That means it'll be easy to install and remove from your vehicle since it's light, but also it'll be very easy to load... view full answer...
The Curt alternative to the Tekonsha # 118758 that I initially recommended for your 2019 Hyundai Ioniq Plug-In Hybrid is the part # C56381. Some of the Curt and Tekonsha wiring are comparable but with your vehicle Tekonsha is using their upgraded module which is why I recommend going that route instead.
The Curt Auxiliary LED Indicator Lights # C53201 is just for the running, stop, and turn signals so you'll need to cut and splice the wiring that comes with the Thule License Plate Holder... view full answer...
You can definitely use the SeaSucker Board Carrier # 298-BX1806 on your 2019 Hyundai Ioniq but this is actually a carrier in and of itself so it doesn't require a roof rack on your vehicle and you wouldn't be able to install your Thule SUP carrier to it.
If you still want to stick with your Thule SUP carrier then I recommend the Yakima JetStream roof rack which consists of 50" JetStream Bars # Y00425 Black, the BaseLine Towers # Y28TR, and the Fit Clips # Y06175 and # Y06111. You can add... view full answer...
For your 2019 Hyundai Ioniq the hitch I recommend is the Curt part # C11486 to carry your bike rack. This hitch has more than enough capacity for a 2 bike rack like the Thule Camber # TH9058 and was made in the USA so it's a really great option. Only the hitch opening hangs below the rear bumper too which makes it less visible as well. I attached a picture of it installed as well as an install video for you to check out too. view full answer...
With the Curt Trailer Hitch Receiver # C11486 for your 2017 Hyundai Ioniq only being a class I receiver you will need to use a bike rack like the Kuat Sherpa 2.0 Bike Rack # SH12G that is compatible with class I receivers. The Kuat will allow for up to 2 bikes weighing 40lbs per bike.
As your Yakima Dr. Tray having the 2" hitch it is only going to be compatible with a class III receivers. Also the Hitch Adapter # 80303 that you saw is only compatible with class II receivers.
Curt does... view full answer...
The best option for a trailer hitch receiver for your 2019 Hyundai Ioniq so you can use a bike rack is from Draw-Tite:
- Draw-Tite Sportframe Trailer Hitch Receiver # 24963
The reason the Draw-Tite is the top option for your '19 Ioniq is because it provides the best clearance from your bumper so your bikes stay safely away from your vehicle, and because it is a no-drill install with a concealed crosstube so just the receiver is showing. That will help your Ioniq retain its factory appearance,... view full answer...
Go To Results