I have added a photo for you from the instructions showing the location where the base plate arms protrude on your 2012 Mini Cooper Clubman after installing the Blue Ox Base Plate Kit # BX1307.
As you can see, you will have to trim the chrome piece on your Mini so the arms have a place to extend out for the tow bar to attach. Speaking of the tow bar, you'll need that along with the wiring and braking systems to flat tow your '12 Clubman, and I'll go ahead and list out below what you need:
-... view full answer...
Mini Coopers are a bit of a challenge when it comes to flat towing. Per Roadmaster's fitment guide the Roadmaster EZ Base Plate Kit # 521877-1 is a fit for S and Clubman models and will work with the Aerodynamic Package, but not with the Sport suspension. With this being such a specific fit I would reach out to Roadmaster with your VIN and any package info on your vehicle to verify with their techs. view full answer...
We do not recommend using the GearDeck Enclosed Carrier part # H00604 with a hitch adapter like a riser as it will cut the capacity by 50 percent for most applications. Now for what you described of using two hitch adapters we would definitely not recommend that as that would be just a bad idea all around. Especially in a lower capacity hitch like what you have installed on your 2009 Mini Clubman. You should note that this only fits 2 inch hitches and your Mini Clubman would have a 1-1/4... view full answer...
Curt does require use of a stabilization strap for their Class I Hitches. Normally, you'd use a Stabilizing Strap like part # 18050 but like many hatchback vehicles, you're running into a simple problem that is easy to fix.
For this, you'll want to purchase part # Y02612 , a set of Yakima Glass Hatch adapters. This part will give you an alternate location to hook the stabilizing strap to that will evenly apply pressure to the padded security bar, removing the need to mount the support... view full answer...
When you're flat towing a vehicle, you want the tow bar to be within 3 inches plus or minus of level. If you're outside that range, you can use a High Low adapter to get you in range. Ideally, you'd be as close to level as possible, but as long as you're within 3 inches one way or the other, you should be fine.
If you need a high-low adapter I've linked our selection. The most popular is part # RM-076 from Roadmaster. I've also linked an article to help you determine how much rise or... view full answer...
Transmission coolers are not vehicle specific so you can install one on your RV. Generally we recommend going with the largest cooler that will fit in the available space under the hood. Or you could go with a stacked plate cooler that is smaller but more efficient. I actually recommend the stacked plate design because they are so efficient. For a kit that comes with a cooler, mounting hardware, hose, and fittings use # D13403. I have also included a link to our help article on transmission... view full answer...
I took a look at the online owner's manual for the 2013 Mini Clubman and it does state that the manual transmission model can be flat towed with all 4 wheels on the ground. I do recommend verifying this information in your copy of the owner's manual, as it's possible you have a different model.
In order to flat tow your Mini Clubman behind your Tiffin Breeze RV, you will need base plates, a tow bar, safety cables, tow bar wiring, and a supplemental braking system.
For a base plate kit,... view full answer...
I spoke with my contact at Yakima regarding the Replacement 1-1/4 Inch Tongue for Yakima HoldUp Bike Racks # 8880581 referenced in your question. She stated that the only additional hardware that will be needed to install the tongue is the existing screws on your HoldUp Bike Rack. You will not need any additional hardware to properly install this replacement part.
This can be used to replace the tongue on the 1-1/4 inch HoldUp Bike Carrier or to convert the HoldUp for 2 inch hitches for... view full answer...
According to Curt, the receiver hitch you referenced, part # C11387 will fit the 2009 Mini Clubman S.
To see installation details, click on the provided link.
The ball mount and a pin and clip are included with the hitch, you might also need the following to complete your towing system:
Wiring Harness with 4-pole Trailer Connector, part # 119250KIT
1-7/8 Inch Trailer Ball, part # 19256
2 inch Trailer Ball, part # 19258
Locking Hitch Pin, part # e98879
You can see the hitch installation... view full answer...
I have a solution for you if you have drum brakes, but I spoke with my contact at Titan and he did not have a recommended way to manually lock out a trailer brake actuator that has an electric reverse lockout.
The best thing you can do is get some free backing trailer brakes. These brakes allow your trailer to back up without activating the brakes, even if your trailer does not have a reverse lockout. Since I do not know what size brakes you have I attached a page that has all of the different... view full answer...
The correct Roadmaster EZ2 Base Plate Kit for your 2012 Mini Clubman S with a manufacturer date of 05/12 is part # 521879-1A, not part # 521880-1. You can use most Blue OX Tow Bars which are listed for you below with this base plate kit so long as you also purchase the RoadMaster Base Plate to Blue Ox and Demco Tow Bars Adapter part # RM-033 and the Roadmaster Tow Bar Quick Disconnect Kit part # RM-201.
Acclaim
Adventurer
Aladdin
Alexxa
Allure
Alpha
Ambassador
Aventa
Aventa II
Aventa LX
Kar Bar view full answer...
If your Mini Cooper Clubman has an automatic transmission, it cannot be flat towed. If it's a John Cooper Works edition, there isn't a base plate available. In either case, you would need to use a tow dolly like the Roadmaster # RM-2050-1.
If it has a manual transmission it can be flat towed with the addition of a tow bar, base plates, safety cables, a wiring solution, a supplemental braking system and possibly a high/low adapter if the height difference between the receiver on the motorhome... view full answer...
I checked with Yakima and the RocketBox Pro 14, # Y07192, is listed as a fit for the 2010 Mini Clubman with factory roof rack. To check for any interference at the rear of the box you will need to take one measurement.
With the front crossbar as far forward as it can go (if it can be moved) measure from the center of it straight back to the seam between the roof and rear hatch/door, or to an antenna. If you come up with 45 inches or more then the box will not interfere with anything.
I... view full answer...
The John Cooper Works (JCW) edition of the 2009 Mini Clubman came with a turbocharged I4 engine. The turbocharged engine also utilizes an intercooler which brings down air intake temperatures. The placement of the intercooler is the reason the Blue Ox Base Plate Kit part # BX1307 will not work for you as they both occupy the same space. Unfortunately, none of our base plate manufacturers (Roadmaster/Blue-Ox) make a base plate kit that is compatible with the JCW edition therefore your only... view full answer...
Please refer to your vehicle specific owners manual for flat towing information, ensure your vehicle can actually be flat towed without damage to the transmission; I understand that some Mini Coopers with automatic transmissions can not. There are five primary components needed for a safe flat towing setup:
1) Tow Bar
2) Base Plate
3) Safety Cables
4) Electrical Wiring
5) Supplemental Braking System
I recommend the Blue Ox Base Plate Kit, # BX1307 for your 2008 Mini Clubman along with... view full answer...
Since you already have the 7-way on your 2010 Mini Cooper Clubman, you will only need the brake controller, and they are universal to all electric trailer brakes. For the brake controller my favorite option and the one I highly recommend is the Brake EVN # TK63VR.
I love the I-Command because it is a great value due to its unique combination of quality and cost-effectiveness. The I-Command is going to give you smooth braking, is easy to use, and has a bright display that is simple to read... view full answer...
The Curt Trailer Hitch Receiver part # C11272 is a fit for a 2012 Mini Clubman John Cooper Works S Edition. It fits other models as well which is why some of the photos will look slightly different than what you may have. The license plate will have to be relocated while the hitch is being used. I suggest moving it down slightly and attaching the top hole on the plate to the bottom hole on the vehicle. It shouldn't matter if it covers the screen in the fascia a bit. view full answer...
I checked with Thule and they confirm that the Thule Pulse L Rooftop Cargo Box # TH615 will fit on the factory cross bars of your 2009 Mini Clubman.
If you do not have a roof rack on your vehicle check out the link I attached that has all of the different Thule racks we offer for you vehicle. You will want to select your roof style and then all of the roof racks available for you vehicle will be listed. view full answer...
Yes. When installing the Draw-Tite # 75151 there is going to be some trimming of the plastic fascia required, since this hitch is a concealed cross tube hitch that mounts behind the bumper on your 2009 Mini Clubman. This may sound a bit daunting, but these modifications are really quite easy and can be done with a hole saw and a standard hand drill. This is the only hitch we have available that is a confirmed fit on your 2009 Mini Clubman.
I've added a photo to show the modification that... view full answer...
Go To Results