I recommend the Curt Trailer Hitch Receiver, # C76WR. This has a maximum gross trailer weight of 3,500 lbs. and a max GTW of 350 lbs. and is a Made in USA product.
For a 4-Pole Flat Trailer Connector, I recommend the Curt T-Connector Vehicle Wiring Harness, # C42WR if your Bronco is equipped with LED lights. If not, select the Curt T-Connector Vehicle Wiring Harness, # C87BR.
If you need a ball mount kit, we have the etrailer Ball Mount Kit for 2" Hitches, # 989900 that includes everything... view full answer...
Yes, it is possible to use a tow bar with your 2021 Ford Bronco Sport. You will just need to use a base plate kit. The Roadmaster Direct-Connect Base Plate Kit # RM79RR is confirmed to fit the 2021 Ford Bronco with a standard bumper. This would allow you to use a tow bar like the Roadmaster Nighthawk All Terrain, Non-Binding Tow Bar # RM-676. The # RM-676 tow bar also includes safety cables which is an essential flat towing part.
You would also need a supplemental braking system and tow... view full answer...
The width of the base rails on the TracRac SR # TH43002XT-781 ladder rack is 4 inches wide. I went ahead and attached a diagram that shows this specification to give you better perspective. view full answer...
For your 2021 Ford Bronco that has the modular bumper the first thing you need is the attachment point for a tow bar like with the # C59JR which is a confirmed fit. With that installed on the bumper you could then use a Curt Tow Bar like the Rambler # C26FR which is easy to use and well made. This also comes with safety cables.
For lighting you can use the diode kit, # RM-15267, and not have to worry about cutting into the taillight housing. This will splice into your taillight wiring... view full answer...
No, you can't. Those hooks are only for recovery or pulling something they're not rated to be flat towed with. You are actually going to have to remove them to install a base plate kit on your 2023 Ford Bronco.
Since you have a Blue Ox Alpha tow bar you'll want the Blue Ox Base Plate Kit item # BLU23XR. This base plate kit is confirmed to fit the Bronco's with the Ford modular front bumper.
Here are some other parts you will need to flat tow your 2023 Ford Bronco:
Wiring Harness -... view full answer...
We absolutely have a Curt trailer hitch receiver that fits your 2021 Ford Bronco; the hitch that fits is the following part:
- Curt Trailer Hitch Receiver # C76WR
The # C76WR is a Class III hitch with a 2 inch receiver and 3,500 lb capacity so it'll meet all your needs for towing or accessories like a bike rack or cargo carrier.
As for the installation difficulty you asked about, it is honestly about the simplest possible install you can find for a hitch. I have added a cut out below... view full answer...
There unfortunately isn't a plug-and-play wire harness to connect your Hayes Syncronizer Trailer Brake Controller # HA81725 to your 2023 Ford Bronco so you'll have to use the universal splice-in wire harness # HA81789-HBC. This harness will need to be wired in the follow order:
Black: 12v power
White: Ground
Blue: Trailer brake output
Red: Bronco cold side of Brake Light Switch
If your Bronco is a base model without the signature LED lighting then the cold side of the brake light switch... view full answer...
The Blue Ox and Curt tow bars have different arm designs at the end so to use the Curt Custom Base Plate Kit # C59JR with the modular bumper on your 2021 Ford Bronco you need to use the Curt Rambler Steel Tow Bar # C26FR. The tab design on the Blue Ox and Curt tow bars can sometimes crossover so that they work with each other's base plate kits but in this case the Curt "base plate kit" is just an adapter that fixes to the tow bar.
For a complete flat towing setup you will need a base plate... view full answer...
Yes, the etrailer part number, # BLU97XR is the Blue Ox part number BX2687. This is a base plate kit for flat towing a 2021 Ford Bronco.
If you do not already have a tow bar, I recommend the Blue Ox Alpha 2 Non-Binding Tow Bar # BX7380 as it features a non-binding type latch that make it easy to unhook tow bar on any terrain; it will also has a swivel function that makes it easy to connect, even on unlevel ground. It also comes with safety cables included so you won't have to purchase... view full answer...
Thank you for your photo.
We offer the K-Source Replacement Side Mirror # KSH3661 for your 1981 Ford Bronco; this is the item you referenced in your question. The top bracket does have only 2 holes, not 3, but it would be easy enough to drill the 3rd hole if you wish. The mirror will be fine if installed with just the two holes that are pre-drilled.
Each hole is 1/4-inch in diameter and they are spaced apart by 3-1/2-inches on centers. view full answer...
As long as the round cross bars on your 1996 Ford Bronco have a diameter less than 4 inches and have a crossbar spread between 24 and 34 inches, then the SportRack Vista XL Cargo Box, # SR7018, will fit.
You can find your crossbar spread by measuring from the center of the front crossbar to the center of the rear crossbar.
I have attached a demonstration video of this bike rack for you to check out. view full answer...
The K-Source Universal Towing Mirrors item # KS3891-2 snap on to the tops and bottoms of the factory mirrors on your 2023 or 2024 Ford Bronco and then you use the included snaps to tighten them down and make sure they're secure.
No, we also have them with flat lenses with item # KS69ZR. These mount in an identical manor but the 7-3/4" tall x 5-1/8" wide mirror face offers a flat view.
We haven't had a chance to test these out on a Bronco but I have linked a couple review videos below... view full answer...
The CIPA Universal Door Mount Mirror, # CM45000, can be used on any application that you choose. They were primarily designed to be used as towing mirrors on GM trucks and vans, but the universal design makes it a great option for almost any towing vehicle.
If you are planning on using this on a large RV such as a Class A motor home, I can tell you that this mirror is probably not as large as the original mirrors. They will also not mount in the same position. The OEM mirrors on most... view full answer...
The roof rack I recommend for your 1996 Bronco is the Yakima roof rack. This roof rack has 66-inch long round crossbars, and includes raingutter towers.
To order this roof rack you will need part # Y00410, and part # Y00101.
The kayak carrier I recommend is the Inno Kayak Carrier w/ Tie-Downs, part # INA455. This system comes with straps to secure the kayak to the carrier and bow and stern tie-downs to secure the kayak to the vehicle. view full answer...
Yes, the white wire from the Hopkins Plug-In Simple Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # HM11140415, that you referenced is supposed to be grounded to a clean metal surface on the body of your vehicle.
I attached the installation instructions also even though they do not mention where the white wire gets run. view full answer...
I really like the Westin Sure-Grip Running Boards w/ Custom Installation Kit # W43PF for your 2-Door 2024 Ford Bronco because these are 6" wide and they have more of an OEM look than a lot of the other options that fit your vehicle. In addition you can install the Westin LED Light Kit # 27-6000 to ensure you can see the running boards clearly in low-light situations. view full answer...
For the etrailer Single Axle Trailer Fender - 16 Gauge Steel - 14" to 15" Wheels, # HP46VR, I called the manufacturer because we don't carry a bracket for that width of fender. The manufacturer says that for that wide a fender, they don't have a bracket and that you'd have to have it custom fabricated. The closest thing we have would be the Smith Galvanized Steel Mounting Brackets for Trailer Fender- 13, 14, and 15 Inch Wheels, # CE26098G-2. This may give you some ideas on what you would... view full answer...
We have the Rampage Replacement Soft Top part # RA98402 which is a confirmed fit for your 1976 Ford Bronco and is white.
For more info check out the install instructions link I attached below. view full answer...
Although we do have running boards available for your 1990 Ford Bronco, the # AA3025165 will not fit. Since there are no motorized options available I recommend the Aries Round Nerf Bars # AA203001. These have a 3" diameter and a carbon steel construction. They come with a custom mounting kit specifically designed for your vehicle. view full answer...
It is possible you can just swap out a 4-lug hub with a 5-lug hub so long as you know the hub you need. And in order to determine this (if you aren't sure already), there's a number of things you'll need to know.
First, you need to know the weight rating of your axle, and also what bearings your current hub has. You will need to take apart your current hub assembly and look at the bearings themselves; wipe away the grease and you should be able to see the part number stamped directly... view full answer...