The diameter of the bolts that works with the CE Smith Padlock Brackets for Spare Tire Carriers # CE26002Z-2 are 7/16 inch.
The brackets are designed to work with the CE Smith Spare Tire Carrier for Trailers - Steel - 4- and 5-Lug Wheels - 8-3/8" Long # CE22007Z-11050-2 and 12-1/4" Long # CE22011Z-11050-2.
I have added a link below to a video review for you to check out as well of the CE Smith Padlock Brackets for Spare Tire Carriers # CE26002Z-2. view full answer...
The Fulton Hi-Mount Spare Tire Carrier # FSTC1000301 wighs in at about 6 lbs.
If you don't already have a tongue weight scale then I recommend picking up our Scale # e99044 because it makes everything easier, plus it weighs under 5 lbs so you can easily take it with you to make sure you have your trailer loaded the best way every single time. view full answer...
I checked with SumoSprings and the # SSR-610-47 that you referenced is 5 inches tall, 8 inches in width, and 11 inches in length with a diameter of 4 inches. view full answer...
The Inno Aero Crossbar System part # INXB108-115, part # INXS200, and part # INK646 while installed will be around 4" tall when measuring from the roof to the top of the crossbar but I don't have any exact measurements for you as this is not a figure the manufacturer provides. I was however able to come up with the above using the height of the mounting foot, mounting foot pad, and crossbar.
I have attached a photo of the height for you on a 2018 Toyota RAV4 as well as an install video. view full answer...
I went out to the warehouse and found that the distance from the center of the jack to the furthest part of the adjustment pin on the Ultimate Trailer Jack # 322-RDJ-2K when it is pulled out is 5-3/8". If you have this much room from the center of your current jack to your winch then this is a great option for you! view full answer...
The depth of the hitch pin hole - or distance from the end of the receiver to the center of the hitch pin hole - of the Curt Trailer Hitch # C13200 is 2-1/2 inches
You were correct about the size of the receiver, it is 2 inches. I have added a link to the installation instructions of this hitch for you as well as a link to a video showing this hitch being installed on an 2018 Toyota Highlander. view full answer...
I went out to the warehouse and found the distance between the bolt holes for the Curt Trailer Hitch Receiver # C13524. Since the two rear holes sit at an angle the distance from back to front is 3" and then 3-1/4" from closest to furthest points of those holes. They are then separated side to side by 37-1/2" on center as you can see from the attached picture.
This is a custom fit for your 2002 Toyota RAV4 and mounts up to pre-existing holes in the frame of your vehicle. I have attached... view full answer...
The Glacier Twist Link Snow Tire Chains with Cam Tighteners - 1 Pair. part # PWH2228SC, per Glacier, has a link size of .23mm. They are rated for highway use and not off road use. The twist link pattern will give a slightly smoother ride than a square chain would.
I have included a video review link and a diagram below. view full answer...
The The OverHaul HD # Y01151-5868 by itself has a 500lb capacity on-road, 300lb capacity off-road, and 800lb static capacity. When using the Tonneau Cover Adapter Kit # Y01155 that changes to a 300lb capacity on-road, 180lb capacity off-road, and the static capacity remains at 800lbs.
Since you're figuring that you'll be over 800lbs you'll have to kick someone out of the rooftop tent and use another option like a rear seat mattress # 341033 or truck bed mattress # 341005 (5' bed) # 341003... view full answer...
I checked with Curt and the Curt 5th Wheel/Gooseneck Custom Wiring Harness w/ 7-Pole Connector - 7 Long Item # C56070 would require 7 inches of clearance on the inner side of the fender/bed wall to install. view full answer...
The wall thickness of the Ultra-Fab Dirt Bike Carrier # UF48-979033 is .115” of the tube that is inserted into the receiver and there is 2 additional strips of steel that is welded inside this tube (.0135” thick) on each side which give us .250” total thickness.
The grade standard mild steel. view full answer...
The Timbren Active Off-Road Bumpstops - Rear Suspension - 3,600 lbs # TABSTRFK have bump stops and mounts that are 5-1/2 inches tall overall and u-bolts that are 8-1/4 inches long and 3-3/4 inches on center. I've attached a photo to assist.
These jounce springs will mitigate sag when towing and they will work great for your off-road towing. view full answer...
The Curt Trailer Hitch Receiver part # C89UR which is a fit for a 2021 Toyota Venza has a class III rating therefore the lowest the tongue weight could ever be is 350 lbs but for this hitch it's actually a bit higher at 525 lbs. The lowest rating a class III trailer hitch can have to maintain the class III is 350 lbs tongue weight and 3,500 lbs gross trailer weight but it can be rated for me as you can see. view full answer...
I do recommend contacting Toyota to see if your 2018 Toyota Prius Prime can be towed on a dolly, though in regards to it being low-profile, there is a guideline by Demco with some measurements you will need to take to ensure it will work.
I have added a cut out from the linked instruction manual, and as you can see, there is a pretty simple formula that you'll use to determine proper clearance, and this is for both the Demco Kar Kaddy X Tow Dolly # DM9713093 and the Demco Kar Kaddy SS... view full answer...
The U-bolts of the Heavy-Duty Crossbar Fit Kit # RUBK that you referenced are zinc coated which means they will do an excellent job resisting corrosion. It would take years of weather exposure for them to start to rust most likely. view full answer...
If your 2011 Toyota RAV4 has a 2-inch hitch receiver like Curt # C13149 then the etrailer Folding Cargo Carrier # e98874 will fit the hitch and will clear the rear of the vehicle even when folded. The etrailer cargo carrier # e98874 provides 9-1/2 inches of clearance from its hitch pin hole even when folded and this is plenty for your RAV4 even if it has the rear spare tire.
In terms of weight capacity the lowest-rated item in the system, between the vehicle, hitch and carrier, determines... view full answer...
I recommend a 2-inch Class III hitch for your 2015 Toyota Sienna over a smaller Class II type since it will give you higher capacity and/or a better safety margin. I suggest Curt 2-inch hitch # C13105 because it has the same capacity as the others but costs less. Written instructions and an install video are linked for you.
In terms of ground clearance all hitches made for your car will mount to the same points on the frame; no one particular hitch will give you noticeably better ground... view full answer...
The linked installation instructions for the T-Rac Pro2 Truck Bed Ladder Rack # TH37004XT include parts descriptions for all of its hardware components.
Item P is a 3/8-16 x 3.0-inch button head cap screw that is used to secure the clamps. Item S is a 3/8-16-1.25-inch stainless T-bolt used to secure the crossbars. view full answer...
Go To Results