I may have a solution for you, but according to my contact at Yakima the Spare Tire Carrier # Y07076 is not compatible with the Basketcase and there is not a tire carrier that will fit on the smaller bars. With that said, you could just use some ratchet straps like the CargoBuckle Mini G3 Retractable Ratchet Straps - 1" x 6' - 466 lbs - Qty 2 # IMF111640 to secure your spare tire. These ratchet straps will provide a bit more secure solution than the cargo net that was included with the... view full answer...
If you're wanting to install an AC unit with a heat pump on your box truck I recommend the Advent Air RV Air Conditioner w/ Air Distribution Box, Start Capacitor, and Heat Strip - 13,500 Btu Item # ACM135CH. This unit comes with an air distribution box that has a built-in thermostat, a start capacitor to help jumpstart the AC so you won't need as high of a starting wattage, and an electric heat strip to keep you warm in the winter.
This unit weighs approximately 100lbs so you'll need... view full answer...
For a threaded Swagman hitch pin that can be used on a 3 inch receiver I recommend using the Locking Anti-Rattle, Threaded Hitch Pin for Swagman Hitch Racks # S64029, which has a usable span of 4-3/8" that will be enough to span the outside of your Ford F-250's receiver. This is a locking anti-rattle hitch pin, but it is the only threaded Swagman hitch pin that is long enough for this particular application. view full answer...
The Thule HideAway Awning - Roof Rack Mount - Waterproof - 80 sq ft # TH490010 can be mounted on your 2016 Mercedes-Benz Sprinter 2500. To mount the awning you will need the Roof Rack Adapters for Thule HideAway Awnings - TH490008 and TH490010 # TH490001.
I have attached a video of the installation and review of the Thule HideAway Awning. view full answer...
I have a really great bike rack solution for you, but the Kuat Transfer V2 # KU84FR can only fit bike tires that are up to 3 inches in width.
So instead, I recommend the Lets Go Aero V-Lectric FAT PRO Bike Rack for 2 Electric Bikes - 2" Hitches - Wheel Mount # LGA77FR. This is fifth wheel approved like you need, has higher weight capacities need for e-bikes of 75 pounds per bike. It has wheel hoops that were designed for fat bikes that will accommodate tires up to 4.5" so that will also... view full answer...
To tow a 16,000 lb 5th wheel trailer with your 2019 Ram 2500 I recommend the B&W Companion OEM 5th Wheel Hitch for Ram Towing Prep Package part # BWRVK3600. The B&W Companion drops down into the OEM prep package of your Ram and features a thick 1" jaw design. The jaw allows for 360 degree king pin contact to eliminate the annoying rattle you may experience with a looser jaw connection of the other brands. The cam action handle makes it so much more convenient to release the king pin even... view full answer...
I do have an option for you so that you can buy the Demco Hijacker 18K part # DM8550034 from your brother. However the Demco Adapter Chevy/GMC OEM 5th Wheel Towing Prep Package part # DM6194 only fits up to 2019 GMC Sierra 2500.
You will need the Hijacker with the Demco 5th Wheel Rail Adapter for Chevy/GMC OEM 5th Wheel Towing Prep Package part # DM6333 which will drop down into the puck system of your 2020 and give you industry standard rails in the bed to attach the Hijacker to. view full answer...
For a 5th wheel hitch on your 2020 Ford F-250 Super Duty I highly recommend the Curt A20 because it is high-performing but not excessive in cost compared to similar hitches. It is also has a sturdy dual jaw system which makes full contact with your king pin to give you a comfortable ride, as well as a color-coded lock indicator which makes the hitch easy to use. The right Curt A20 will depend on if your 2020 Ford F-250 has the factory fifth wheel prep package or not:
- With Factory Prep... view full answer...
The 15" term is in reference to the size wheel that the Provider ST225/75R15 Radial Tire is mounted to. This particular part # A225R6FPS is a tire and wheel combo. The wheel has a 6 on 5-1/2 bolt pattern which is important to know so that your hub will fit. I have attached a helpful article regarding measuring for bolt pattern if you are not sure of your bolt pattern.
The LRD is in reference to the Load Range which is a load range D in this case. The different load ranges have different... view full answer...
I recommend the Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit part # 75282 because it has a higher towing capacity compared to the other options. It also a concealed cross tube design for a discreet OEM look on the Frontier. The only portion of the hitch that is visible is the square receiver tube. I have attached an installation video and photos for your reference.
For the wiring, I recommend the Tekonsha T-One Vehicle Wiring Harness with 7-way Trailer Connector part # 118266... view full answer...
I recommend the Wraparound LED Tail Light for Trailers Over 80" Driver's side part # 271595 and part # 271594 for the passenger side. The Wesbar Wraparound LED tail lights measure 7" long x 3-3/4" tall x 3" deep with mounting holes 2" apart. You will want to measure you mounting hole pattern and your existing lights to make sure they will mount without drilling new holes. I have attached a diagram for your reference.
The LED replacement will draw less power, last longer and illuminate... view full answer...
The minimum cross bar spread to install the Thule Hullavator Pro Kayak Carrier and Lift Assist with Tie-Downs part # TH898 is 24" apart. So the bars must be at least 24" apart for safe use. The maximum cross bar spread is 36" so it only fits cross bar spreads up to 36" apart. To make sure that your cross bar spread fits in this range you can measure from the center of the rear bar to the center of the front bar for the crossbar spread.
It also requires 28.5" of load bar space with 4-8"... view full answer...
The only way to carry a kayak and/or canoe on the 2020 Ram 1500 while towing is to install a roof rack on the truck and use a carrier. I recommend the Yakima JetStream Crossbars part # Y00427 because they are aerodynamic and their built-in ridges help control air flow to cut down on wind noise. They also have a nice T-slot channel that allows you to mount accessories with a rubber strip that does not need to be trimmed to add accessories like other brands. You will also need the BaseLine... view full answer...
The Curt Trailer Hitch Receiver part # 13920 is designed for a 1982 - 2004 Chevrolet S-10 Pickup with roll pan bumper so this will be the best option we can offer. It's hard to say whether or not the trailer hitch will line up with the license plate area but if you measure down from the upper mounting holes the top of the receiver tube will be around the 2-1/2" mark. view full answer...
The big difference is the corners of the main panel of the # FV807357 are cut out with small section to allow access to mounting hardware and the # FV807359 instead does not have this area cut out. So you'd want to look at your vents to see if you need the cutouts or not. view full answer...
The Hollywood Racks RV Rider Bike Rack for 2 Electric Bikes - 2" Hitches - Frame Mount,Item # HLY64FR can carry 2 e-bikes weighing up to 80 lbs each. This is the only rack that will work with both a step-through bike and fenders.
This carrier can accommodate tires up to 5 inches wide and wheelbases up to 60 inches. You can see a product demonstration video by using the provided link. view full answer...
The correct SumoSprings Custom Helper Springs for a Newmar Canyon Star 3810 is part # SSF-173-40-2 for the front and part # SSR-187-54-1 for the rear. view full answer...
The SportRack Replacement Hardware Kit for Explorer and SkyLine XL Roof Mounted Cargo Boxes # SR05587 has basic components for mounting. Just the crossbar mounting hardware for this kit is found in the Replacement Hardware Kit for Searsbox Cargo Box # TH05603. Not all of those components are available separately, so you will want this kit for all those parts.
Not all mounting hardware will work with this box even retrofitted, so if you want further options for your crossbars, you may... view full answer...
The Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # C56148 is a confirmed fit for the Nissan NV 1500, 2500, and 3500 models between 2012 and 2020. There is not a separate fit for the cargo models from the passenger models because they utilize the same wiring. You can alternatively use # 118553 or # HM11143585 which are also confirmed to fit. These are all good options, so I recommend going with the best cost at that time of purchase. view full answer...
Since your steps were built before 1999, what you will need to do is upgrade your motor, gear box and linkage; individual replacement parts will unfortunately not work.
So what you are going to need is the Motor Upgrade Kit for Kwikee Electric RV Steps # LC379145.
This includes a switch kit and integrated motor, gear box, and "A" linkage which will get your steps working again. I've added a link to a video review for you as well. view full answer...
Go To Results