Your jumper box may fit in the WeatherTech Under Seat Truck Storage Box - Black # WT43SV, but unfortunately WeatherTech was not able to give me accurate dimensions to verify this for you. I would look into the Husky GearBox Interior Storage System # HL09411 which I do have some dimensions for. This tray has a compartment area on one side which measures 11" by 9" and 6-1/2" deep. This box is confirmed to fit 2021 Ram 1500 Crew Cab. view full answer...
I had our warehouse workers pull WeatherTech Under Seat Truck Storage Box - Black # WT56HR to get that measurement for you. At the deepest point it is 6" and at the lowest point it is 4". This is confirmed to fit your 2014 Toyota Tundra view full answer...
The Bestop Underseat Locking Storage Box # B4264101 that you referenced measures 12" long x 8" wide x 3" tall. We haven't test fit it on a Toyota Highlander but you can use these dimensions to determine if you have enough room under your driver's seat. view full answer...
According to the vendor, Du-Ha Truck Storage Box and Gun Case - Behind Seat - Black # DU20025 measures approximately 50" long, 6.5" wide, and 6.5" tall. This is made to fit behind the seat on 2000-2007 Ford trucks.
While there is not a 'behind seat' storage box for your 1963 Chevy pickup, you could always look into a truck bed storage box. Buyers Products Utility Storage Box - Black # 3371712240 is confirmed to fit your vehicle's bed. It measures 44" wide x 19" deep x 17-1/4" tall. I attached... view full answer...
The storage box for the Titan Chain Alloy Snow Tire Chains # TC2317 will comfortably fit in a 14-1/2" x 14-1/2" opening, but you might be able to squeeze it into a 14-1/4" x 14-1/4" opening if that's all you have available. It's only a few inches thick so it can easily be stored under some seats in a worst case scenario. view full answer...
Yes, the Du-Ha Truck Storage Box and Gun Case # DU60051 can hold two rifles with scopes, or two shotguns. It is legal in most states for this application. This tough polyethylene storage unit fits the 2008 Tundra double cab (trucks without the under-seat audio system subwoofer) and matches the vehicle interior. Mounting hardware is included.
Thanks to its adjustable cargo divider panels this unit can be configured for other contents apart from hunting gear. The panels allow you to choose... view full answer...
There are no storage boxes that are confirmed to fit your 1995 Ford F-150, but I can give you the dimensions of the box you were looking at so you can verify fitment with your truck. The Du-Ha Truck Storage Box and Gun Case - Behind Seat - Black # DU20054 that you were looking at measures 50" long, 6-1/2" wide, and 6-1/2" tall according to Du-Ha. This attaches to the floor with the included hardware; drilling is required. view full answer...
The Kelty Essential Camp Chair # KE64AR has an overall height of 36" and the Kelty Deluxe Lounge Reclining Camp Chair # KE54AR has an overall height of 38-1/2". view full answer...
I may have a solution for you, but the top of the box of the UWS Truck Bed Fender Well Toolbox with Drawers - Passenger's Side - 3.9 cu ft - Bright Aluminum # UWS01625 sits 4" above truck bed rails, so it will not work with a tonneau cover. Instead, you could use the UWS Truck Bed Chest - Secure Lock Under Tonneau Series - 8.85 cu ft - Bright Aluminum # UWS08297 which is designed to fit underneath a tonneau cover and provides you with a locking storage solution. It's quite a bit bigger... view full answer...
We don't have specific dimensions for the # VRF92 but to answer you real question-it covers the entire floor from behind the front seats to under the cargo door's plastic shroud.
I attached a picture that shows how it covers the floor of a vehicle. Your vehicle may be different, but the concept is the same. view full answer...
I reached out to Lippert to get the inside measurements of the storage bins for the Lippert Underchassis Double Bin Storage Unit for RVs - 96" Long # LC175180.
I was told the bins were slightly under 17 inches wide (about 16-15/16 inches), measured 25-7/8 inches long, and the height from the ridges was approximately 5-5/8 inches.
I have added a link below to a video review for you to check out as well of the Lippert Underchassis Double Bin Storage Unit for RVs - 96" Long # LC175180. view full answer...
The Replacement Trailer Hub Bearing # 25580 is traditionally the outer bearing for a #99 spindle with the inner bearing # 28580. For instance the Trailer Hub and Drum Assembly - 7,000-lb Axles - 8 on 6-1/2 # 99865UC3 is a fit for your axle and is intended for the 7,000 lb axle which is what I assume you have. Both the bearings and grease seal are a confirmed replacement. view full answer...
I have attached a diagram I made that shows the dimensions of the Storage Bag for Telesteps Telescopic Ladders item # TE59FR. It is 6" x 18" x 32" and weighs just under 2 lbs. view full answer...
I checked with the manufacturer and the inside height of the Buyers Products Utility Storage Box # 3371712230 is 11-1/2 inches and its width is 29 inches. So if your gallon jug of oil, windshield washer fluid or engine coolant is just under those dimensions it will fit!
I have added a link to a video review of this storage box for you to check out as well. view full answer...
Yes, you will be able to get the theater style seating in the 24" wide door on your 2019 Keystone Cougar. The Thomas Payne Arm Recliners like # 195-000086 have a removable back section that make it much easier to get inside your Cougar. The seat height is only 20" from the ground as seen in the picture below and you will be able to turn the base of the sofa to get the taller arm portion to fit in the door. This allows it to fit inside door openings as narrow as 22".
For the removal of... view full answer...
I have a solution that could work for you, but we do not sell air kits for trailer suspension to raise the ride height.
You can do this by moving the axles from being above the leaf springs to below the leaf springs.
The diameter of your trailer axle will determine the size of the parts that you will need to order. If your axle is 3 inches diameter, the Dexter Trailer Springs Over-Under Conversion Kit, # K71-385-00, would be a great choice and if your axle is 2-3/8 inch diameter you could... view full answer...
The top tray on the MORryde Camping Kitchen with Storage Compartment for Jeep Wrangler # MR83MR measures 0.947" so you're looking at just under an inch tall, which I confirmed with my contact at MORryde.
Hope this helps you out! view full answer...
When install an over-under conversion on a trailer you will end up raising (or lowering if that is the goal), the trailer the thickness of the axle, the spring seat, and the thickness of the leaf spring used.
Since those factors can vary widely I don't have an exact number I can give you. view full answer...
First, you would need to have the spring seats welded to the top of the axle. You cannot flip the axle because then the existing spring seats would be bent the wrong way. What you can do is measure from where the springs are attached to the spring seat now up to the top of the axle to determine the approximate amount it will raise the trailer when using the Dexter Trailer Springs Over-Under Conversion Kit, # K71-385-00.
To use this kit you will need to have a 3 inch diameter axle. When... view full answer...