Nope, the trailer wiring is a separate purchase for your 2017 Nissan Rogue Sport, and does not come with the etrailer Trailer Hitch Receiver # e79YR.
The correct trailer wiring harness for your '17 Rogue Sport is the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # C56397. view full answer...
The wire that you see in the pictures for the Curt Trailer Hitch, # C11290, is called a fishwire or bolt leader. It is used to pull bolts and other hardware needed for hitch installation into place in hard to reach or otherwise inaccessible places on the vehicle frame. I have included a link to the installation details for this hitch below.
The Curt Trailer Hitch, # C11290 will allow you to tow a trailer but you will need a separate wiring harness to power the lights on the trailer. The... view full answer...
What kind of info are you trying to find out? The VIN for your trailer should be on the bill of sale so if you know where that is you can use that. Otherwise your best bet to get specific info on your boat trailer would be to contact the manufacturer if you know who that is.
If you are looking for replacement parts for your trailer just let me know and I can see if we have anything that will be compatible. view full answer...
Yes, the Trailer Valet XL Trailer Dolly with Chain Drive # TVXL25 does come with the Drill Attachment for Trailer Valet XL # TVDA included. The # TVDA will also be the correct Replacement Drill Attachment should you need a replacement or extra drill attachment. view full answer...
Yes. Trailers like the Malone MicroSport Trailer # MAL24ZR do come with a VIN number so that the trailers can be registered and legally towed on roads and highways, regardless of where you live. There are a lot of great options available for kayaks depending on how many you need to carry, so I've linked all of the kayak trailers we have available to this answer for you. view full answer...
The Curt Trailer Hitch Receiver part # C11831 is the only available trailer hitch option for a 2006 Saab 9-5. It does not come with any trailer wiring or ball mounts/hitch balls because not all those who use a trailer hitch do so for towing. That said, we do have all these parts you need. The Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector part # C59236 is what you need to operate the trailer lights and the Curt Class II Drawbar part # C45521, Curt Class I and II Pin... view full answer...
It's very common for smaller single axle trailers to have brakes installed on them already. Most likely if you look you'll find options in the size you want that are already set up with brakes. This would be the easiest and most cost efficient way to go, but if not I attached a help article on adding trailer brakes to a suspension axle for you to check out as well. view full answer...
Yes, the Trailer Valet RVR3 Remote-Controlled Trailer Dolly w/ Hitch Ball Mount - Wireless Remote - 3,500 lbs, part # TVRVR3-BB225, comes with the 2-5/16" hitch ball and mount. We do sell each of these items, the RVR3 Trailer Dolly and the Trailer Valet Combo Ball Tower Mount, separately. This item includes both parts.
I have included a product description link and video reviews of the Trailer Valet, without the ball, and a video review of the ball, without the dolly, below. view full answer...
The Swagman XC 2-Bike Rack for 1-1/4" and 2" Trailer Hitches # S64650 is a great platform bike option for your 2003 Subaru Forester, so long as it is already equipped with a trailer hitch receiver, like the Draw-Tite Trailer Hitch Receiver # 36311, designed to fit the frame of your Forester.
To use the bike rack, you do not need any extra parts. Everything you need to install it on a trailer hitch is included with part # S64650.
The only time you'll need to use a ball mount, is for trailer... view full answer...
Part # RA-28, the Rack'em Fitz-All Enclosed Trailer Ladder Rack system, consists of two complete cross bars and the four mounting tabs needed to install them. The distance from the top of the crossbar down to the top of the mounting tab is 15-inches. The actual height of the bar above your roof vent depends on the specific vent, but I expect that virtually any trailer roof vent will easily clear the underside of the bars.
This rack's 400-lb capacity is plenty for your 250-lb box but you... view full answer...
Technically this is a trailer package that is built using existing Yakima components, but all in one part number. Unfortunately we haven't had a chance to get a photo of this particular setup as it's a newly offered product.
The Yakima Kayak Trailer for 2 Kayaks and 2 Bikes # Y34TR uses the Yakima Rack and Roll Trailer with 66" Crossbars # Y08106. The trailer then has a Yakima JayLow Kayak Carrier w/ Tie-Downs - J-Style or Post Style - Folding - 1 or 2 Kayaks # Y04073 added, along with... view full answer...
Electric Trailer Brake Kit # AKEBRK-35-SA includes the left and right side assemblies but not the drums. We have numerous drums available for 3,500 pound trailer axles. I have included a link to them for you.
You mentioned adding brakes to the trailer. If the trailer does not already have brake mounting flanges on the axle(s) then those will have to be added. Adding them is a precision job that requires someone with experience to weld them on. I have included a link to our help article... view full answer...
The Rackem Trailer Dolly, # RA20, only comes with a 1-7/8 inch ball. A 2 inch ball is not available for this item. Proper ball fit is necessary when towing, but it is not necessary when moving a trailer with this dolly. This dolly can even be used with trailers that require a 2-5/16 inch hitch ball.
As long as the tongue weight of your trailer does not exceed 500 lbs and you can physically pull the weight yourself, then this tow dolly will support your trailer with the 1-7/8 inch ball. view full answer...
If you have a single axle trailer you would need to order two Trailer Hub and Drum Assembly part # AKHD-550-35-EZ-K as they are sold individually. view full answer...
The Timbren Heavy-Duty Axle-Less Trailer Suspension # ASR2KHDS05 comes in a pair so you would only need to purchase one to replace one axle on your trailer.
If you have a tandem axle trailer you will want to replace both axles with this type of system. For applications that have more than 2 axles a standard trailer axle will need to be used.
I have attached an installation video for you to check out as well. view full answer...
The Pro Series Trailer Jack, part # PS1400960376 does not come with an extension for a handle.
The handle, part # PS1400920383 is sold as a separate item.The # PS1400920383 handle will extend 13-1/2 inches when installed which should give you the needed room at the side of your trailer. view full answer...
The Buyers Products Hook and Keeper for Enclosed Trailer Door part # BP64FR does not come with hardware as the hardware required will vary from trailer to trailer. That said, there isn't anything needed that you can't find at a local hardware store. You'll basically just be using wood screws that can grab onto the trailer walls without going through. view full answer...
I was able to confirm with my contact at Optronics that the Aero Pro Trailer Light Kit # TL16RK uses 20 gauge wiring for all of the wiring that comes in the kit, including the 4 way harness. view full answer...
The Curt Hitch part # 13703 is a very universal trailer hitch that can be installed on I-beam frames like what your trailer has, the bend in the hitch brackets will accommodate your frame. This would be a great option for you. I attached an install video for you to check out as well. view full answer...