The correct Coil SumoSprings that fits your 2018 Nissan Pathfinder is the part # CSS-1195R. The other part number is basically just slightly different dimensions so it won't fit your vehicle well at all. view full answer...
The Kat's Heaters Custom Engine Block Heater # KH11412 will install in the front right of your 2016 Nissan NV2500 with the 5.6L V8. I've attached a diagram to assist. You will also want to use a thread sealant like # LT37482 or # LT37615.
It is not quite as simple as unscrewing the plug and screwing in the heater, but it is close. You will need to drain your cooling system first because the plug gets immersed in coolant. Other than that, it is basically unscrewing and then screwing... view full answer...
On the 2010 Nissan Frontier, if the vehicle did not come with a factory tow package it will not have a functioning wiring harness even if the Tow Ready Wiring Harness, part # 118263, is added. There will be relays that will need to be inserted to make the trailer wiring harness fully functional. The relays are not normally included on a vehicle if it does not have the factory tow package.
Usually, the relays would be installed in the relay box under the hood if it came with the factory... view full answer...
The Yakima BaseClip Fit Kit # Y06123 is for the front and the Yakima BaseClip Fit Kit # Y06170 is for the rear. Then you can install your Yakima BaseLine Towers Y00146 and then whatever Yakima crossbars you have. view full answer...
Technically you could splice into this outlet for since it does have a 10 amp fuse but you'd have to ensure the T-One Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # 118480 is the only thing on this line and would render the outlet useless. If you plugged anything else into this outlet you'd likely pull too much and blow the fuse.
Personally, I recommend running the line to the battery directly to ensure that the ModuLite is receiving the correct amount of power and won't... view full answer...
Thanks for the information and photos of the Saris Bones 2 Bike Rack # SA805BL on your 2018 Nissan Leaf!
The guide Saris has for installing that rack on your vehicle is to place the lower feet into the license plate well as opposed to on the bumper like what you have. Typically when we see this type of note it's because the bumper isn't strong enough to hold the weight of the rack and bikes.
As far as the middle straps go, it's usually best to try to get them as horizontal as you can... view full answer...
To install the Curt trailer brake controller wiring harness # C51382 you will need to locate the factory harness. The harness is located underneath the dash, to the left of the steering column, taped to another harness near the emergency brake pedal. I have linked a video and some instructions on another harness that fits that should help.
The Curt trailer brake controller wiring harness is compatible with Curt brand brake controllers that accept the plug, like the Echo Under-Dash # C27JR.... view full answer...
So long as you wire the side view cameras to the running light circuit, they will stay on continuously when using the Furrion Vision S Wireless RV Observation Camera System w/ Side Marker Light Cameras # FCE48TASL-05.
When wired this way, the side cameras of the Vision S # FCE48TASL-05 won't just come on when the turn signals come on, and the monitor even has a tri-view display option so you can see both on the sides and behind you. view full answer...
It sounds like you're referring to the factory plug that's used for a brake controller adapter; it doesn't appear that the 2000 Nissan Xtrerra came with one so any brake controller must be hard wired into the vehicle. For this reason, when installing the # ETBC7 in addition to the 12v power line you'll need to run a wire for a brake output wire into the cabin of your vehicle.
If you still need a brake controller, I recommend using the Tekonsha Prodigy P3 # 90195 because provides proportional... view full answer...
The TrailSeal Tailgate Gasket- Bulk Roll # 834532001583 would be a really great solution as a tailgate seal for both your 2006 Nissan Frontier and the 2004 Dodge Dakota. view full answer...
You can use that wire, but you will want to install the 40 amp breaker that came with your # ETBC7L. The Echo # C51180 won't pull that much power but the combination of the brake controller and the trailer would cause your 20 amp fuse to blow. view full answer...
In regards to the TruXedo Lo Pro Soft Roll-up Tonneau Covers like part # TX597301, there isn't a torque value for the rail clamps. If you're having trouble with the rails staying flush to the bed, have a friend put some pressure downward on the rail as you are tightening the clamps. You also need to be sure the teeth on the clamps are aligned with the grooves on the rail. view full answer...
Thanks for the purchase of the Curt T-Connector Vehicle Wiring Harness for Factory Tow Package - 7-Way Trailer Connector # C56226 for your 2020 Nissan Frontier, and the 7-way will have the 12 volt pin active after the installation.
Installing the 7-way will require you to plug in two different harnesses, one of which is the relays (which come with the # C56226). If you take a look at the photo I added, you can see exactly where this will install on your 2020 Nissan Frontier; it will be... view full answer...
Having a tow package already on your 2004 Nissan Frontier certainly makes it easier. What you will need to do to install a brake controller will depend on which factory tow package you have. Generally speaking, there is not a simple "plug and play" option available. However, the Tekonsha Prodigy P3, part # 90195, is a great choice that has an easy set up and is easy to use. To install your brake controller, you will need to "wire" together the brake controller and the trailer connector.
If... view full answer...
You are close on your install but have a few more steps to go. The blue wire in your Silverado is your "brake wire" for any trailer. It needs to be connected to the brake wire of your 7-Way connector. In order to make this connection, you will need to use a "double bonded" wire which we have in installation kit # 5506. This kit also includes breakers and attaching terminals which you may need. The steps to complete your installation are:
1. Connect one end of the 25 ft "double bonded"... view full answer...
The Curt Discovery Trailer Brake Controller, # C84VV, should show only the decimal point dot when the controller is activated and a trailer is not connected. If it shows the dot all the time, the red wire is connected to the wrong side of the stop light switch or the wrong switch completely like the cruise control.
If you have only the decimal point when the trailer is connected, the usual cause is that the brake controller does not sense the trailer brakes. This could be due to corrosion... view full answer...
The installation bolts should be M12 x 1.25 x 30, a hardware store should be able to confirm that the bolts you were provided are that size for you, but it's probably not necessary.
In the almost 14 years I've worked here, I've heard of less than a handful of cases where the incorrect hardware was included in a hitch kit, so it's incredibly likely that there's still some rust and debris up in the frame nuts that are preventing your from getting those bolts to thread. Even though your... view full answer...
I see from your recent order that you purchased the Tekonsha Primus IQ brake controller, part # TK90160 and the wiring harness adapter, part # 3050-P. You can simply plug one end of the adapter into the back of the brake controller and the other end into the port located under your dash near the emergency brake pedal and will be taped to another wiring harness.
The # 118266 you purchased will plug into the two connectors on the driver side frame rail near the back of the vehicle. You... view full answer...
I have linked a video that should help with the installation of the tow package relays on your 2012 Nissan Titan. I tried to look up the exact locations but this information is not provided in the vehicle owners manual. There should be a legend on the inside cover of the fuse panel(s) (one under the hood and possibly one in the truck cab). view full answer...
Adjusting the Hitch ball on your weight distribution head is a two step process. You will first need to adjust the height of the hitch ball. Park the trailer on a fairly level surface and measure from the ground to the bottom of the coupler, then measure from the ground top of the weight distribution hitch ball. Adjust the hitch ball to between 1/2 and 1-1/2 inches higher than the coupler height in the most upright position.
After the height adjustment is made you will then be able to... view full answer...
Go To Results