Expert Answers about Nissan Titan

• How to Activate the Tow Package Wiring on a 2012 Nissan Titan
• If your 2012 Nissan Titan did not come with the factory tow package, then there will be some additional relays that you will need to install to activate the trailer wiring on your truck. You will need the Curt Relay Kit, # C57000. This kit includes three relays that will need to be installed in the power distribution box under the hood. I have attached an installation video of this relay kit on a 2011 Nissan Titan for you to check out. The installation will be the same as your 2012 Titan.
  view full answer...


• BAKFlip G2 Hard Tonneau Cover Installation On A 2021 Nissan Titan 5.5' Bed With Utili-Track System
• To install the BAKFlip G2 Hard Tonneau Cover # BAK26525 on your 2021 Nissan Titan 5-1/2 Foot Bed with Utili-Track System you'll need to follow the steps listed below: 1. Slide the front half of the clamp into the rail in the tapered slot. Position the clamp as close to the front of the rail as possible, it should be less than 12” from the front. Place the second clamp near the center of the rail. Position the rear clamp as close to the tailgate as possible. 2. Slide the back half of...
  view full answer...


• Relays for a 2012 Nissan Titan
• We do have the Curt Relay Kit for Nissan Aftermarket Tow Package # C57000 if any of the relays on your 2012 Nissan Titan need to be changed out. I have attached a video of the kit being installed on a 2011 Titan that you can use as a reference, but you will want to check your owner's manual to verify any fuse or relay locations. It is also possible that some wiring could be damaged or you could have some debris or corrosion inside the connector on your Titan or your trailer. Let me know...
  view full answer...


• Installation Instructions for the Curt Front Hitch # 31199 On a 2008 Nissan Titan
• It looks like you bought the Curt Front Hitch part # 31199 for your 2008 Nissan Titan. I attached a set of installation instructions for this front hitch to the right.
  view full answer...


• Can the Curt Cargo Carrier # C18152 Mount Onto the Front of My Truck?
• Yes, the 24x60 Curt Cargo Carrier # C18152 can be mounted on the front of your truck if you have a front 2-inch hitch. To mount it to your hitch you can use Pin and Clip # PC3 or to protect your investment you can lock it to your hitch with Trailer Hitch Receiver Lock # e98880. You may also be interested in the Cam Buckle Tie-Down Straps # IMF12637 and Curt Stretchable Cargo Net # C18200 if you have gear you don't need to keep out of the elements. If you need a front hitch recommendation...
  view full answer...


• How To Power Third Brake Light On Camper Shell Using 7-Way Trailer Connector
• Yes, you can use the factory trailer connector on your 2015 Nissan Titan to power the third brake light on your Leer camper shell. That said, they don't make a plug and play harness for this so you will need to do some wiring but no splicing into the vehicle will be required. Basically, all you need is the Pacer Performance 3rd Brake Light Logic Module part # PP20-702, the Pollak Black Plastic RV-Style Trailer Connector part # PK12706 and then some loose wire and connectors to attach it...
  view full answer...


• Trailer Lights Not Working When Using Tow Ready Wiring Harness, # 118384, On 2007 Nissan Titan
• The Tow Ready Wiring Harness, # 118384, is for a Nissan Titan with the factory 7-Way trailer connector. It will plug into the back of your 7-Way on your vehicle and the other end will plug into the tow vehicles trailer harness connector, behind the bumper on the drivers side. This harness does not come with relays because they are usually installed already when the factory 7-Way is on the vehicle. You might check the accessory fuse block to make sure you have the three relays installed...
  view full answer...


• Torque Specification for Timbren Rear Suspension Enhancement System
• I just spoke with my rep at Timbren to get the Torque spec's for the Timbren Rear Suspension Enhancement System item # TTORTUN4. She said that they do not specifically list Torque specifications because each part isn't specific to any certain manufacturer. You will want to hand tighten the bolt and then tighten it to 30-35 ft-lbs but make sure you stop before the metal bends.
  view full answer...


• Installation of 7-way Trailer Connector on 2006 Nissan Titan
• Yes, we have a kit, item # N40975 that will hook up to your existing wiring and provide a 7-way connector on your 2006 Nissan Titan. The kit includes the vehicle end 7-way trailer connector, relays and mounting bracket. You will have to install the relays under the hood in the passengers side fuse block (see video link). The port for the trailer wiring harness is located behind the rear bumper near the spare tire on the driver side.
  view full answer...


• Is Relay Required for Trailer Running Lights on 2015 Nissan Titan
• If you have already installed the Curt Relay Kit # C57000 on your 2015 Nissan Titan, and are still having difficulty with the running lights on the trailer, then a 3rd blue relay will be needed to activate this function. Since we do not sell then separately, you would need another Kit # C57000, then you would heave extra relays left over. This relay should be located in the box under the driver-side dashboard, to the left of the steering column.
  view full answer...


• 2015 Nissan Titan Brake Controller Installation via Hardwire
• I have a solution for you but I was unable to find any wiring diagrams that specify which wires are which on the 2015 Nissan Titan. Because of this, you'll need to manually trace and test each wire to determine which wire controls which function. In order to test each wire, you can use a circuit tester similar to # PTW2992 and check the factory harness to determine which wire is the power and which wire gives a signal when the brake is pressed- the ground and Brake Controller Output won't...
  view full answer...


• Can Andersen Ultimate # AM3200 be Reversed with Offset Facing Cab on a 2017 Nissan Titan
• You definitely can reverse the Andersen Ultimate Connection 5th Wheel Trailer Hitch # AM3200 so that the offset is more towards the cab if that suits your towing needs better. Just as you said, it is best to keep the pin weight (or tongue weight) over the middle of the rear axle on your 2017 Nissan Titan.
  view full answer...


• Installing a Brake Controller on a 2004 Nissan Titan with Factory Tow Package
• The folks at the Aluminum Trailer Group sent you to the right place. There are a few different routes you can take to install a brake controller on your 2004 Nissan Titan. Since it came with the factory tow package, you could simply purchase the Tekonsha Prodigy P3 Brake Controller, # 90195, and splice the included universal harness to your OEM harness that was included with the truck. The wires on the brake controller harness are listed below. Black - 12v Battery Feed Blue - Brake Output...
  view full answer...


• Is it Legal to Use Prostrobe Rocky 8 Pro - White Windshield Light Strobe Light on a Vehicle
• Prostrobe Rocky 8 Pro - White Windshield Light # PRS70747 should only be used in emergency situations. For example if the vehicle is stalled on the side of the road and you need to be visible to other drivers. It isn't something you would want to use all the time when driving around because it is not DOT approved for that purpose.
  view full answer...


• Does the Plug on the etrailer Tongue Weight Scale Need to be Perforated
• The sticker you are looking at on the etrailer Tongue Weight Scale for Campers and Utility Trailers - 2,000-lb Capacity # e99044 can be ignored. This is for the installation of the gauge, but the gauge already comes installed. The only thing you need to do is follow the assembly instructions included with the scale.
  view full answer...


• Brake Controller Plug Location on 2018 Nissan Titan
• To install the Draw-Tite Activator Brake Controller # 5504 that you referenced on your 2018 Nissan Titan you will need the Plug-In Wiring Adapter # 3050-P. One end of the adapter plugs into the brake controller itself and the other end will connect right to the factory port that's located behind the dash, on the left hand side by the emergency brake pedal. There is a dash panel there that needs to be removed to gain access to the plug, which should be white in color and labeled "Electric...
  view full answer...


• How Does the Pop & Lock Custom Tailgate Lock Install on my 2014 Nissan Titan SL Tailgate
• I have linked a copy of the instructions for you on how to install the Pop & Lock Custom Tailgate Lock part # PAL8410 on your 2014 Nissan Titan. This will walk you through the process step by step and get you through the installation quickly.
  view full answer...


• Will Timbren Suspension Enhancement System Increase Payload of 2012 Nissan Titan Pro 4X?
• Adding suspension enhancement like the Timbren # TNRTTN you referenced does substantially help with load support and reducing sag, however it does not increase the payload capacity of your truck. Your 2012 Nissan Titan Pro 4X will have the same 1850 lbs of payload but the system will assist with stability by reducing squat, reducing body roll, and assisting with shock absorption. It will assist far better than adding a leaf spring as that will change the ride of your truck when not...
  view full answer...


• 7-Way Diagram to Use for Wiring Up Pollak 7-Way part # PK11-934
• I attached a 7-way diagram that you can use as a wiring guide for installing the 7-Way kit part # PK11-934 that you referenced. You'd want to use the middle picture's wiring colors.
  view full answer...


• Can the Switch for the Hopkins Trailblazer Electronic Deer Alert be Installed Inside of the Vehicle
• First, you can install the switch for the Hopkins Trailblazer Deer Alert, # HM27512VA, in the cab of the vehicle. You would just need to route the wires that lead from the switch to the alert through the firewall to the alert. The only restriction is the length of the wire. You may need to extend the switch wires if they do not reach from the alert to the inside of the vehicle. This installation method may require drilling through the firewall if the wires cannot be routed through an existing...
  view full answer...