If you have a 1999 Nissan Frontier with the king Cab, we do have several Tonneau covers that will work for you. The cover you referenced, part # 554119 is not designed to work with a Nissan Frontier.
The Craftec Tonneau Cover, part # 654517, will work with your over-the-rail bed liner, but when installing you will be required to cut and remove the part of the bed liner to allow the clamps to be secured to the bed rail, or it will not fit correctly.
Many people use a bed liner and a tonneau... view full answer...
Since you verified that the 7-way connector installed on your 2005 Nissan Frontier Diesel is working properly, and only the brake lights are not working it sounds like there is a bad ground which can cause all sorts of weird issues.
If your brake lights have a ground wire to them, I recommend checking that the ground securely attached to the frame and that there is no corrosion or rust that would cause a bad connection. If the trailer has a tilt bed, folding tongue, or is aluminum running... view full answer...
The only change you would want to make is that instead of the Universal Wiring Adapter for Curt Brake controllers # C51515 you would have wanted to get the Curt Custom Wiring Adapter # C51382.
This will make the installation of the Curt Triflex Brake Controller part # C24VV simple. All you would have to do is plug one end of the connector into the back of the brake controller and the other end to the harness that is located underneath the dash, to the left of the steering column, and... view full answer...
For your 2024 Nissan Frontier I recommend the etrailer Trailer Hitch Receiver # e98869. This is a Class III hitch with a 2" receiver and a max gross trailer/tongue weight of 5,000/500 lbs. This hitch also features a matte black powder coat finish. The finish gives it an OEM look while hiding dirt and dings. It has a bolt-on installation and comes with a lifetime warranty.
For a 4-way you can use the Curt Powered Tail Light Converter with 4-Pole Flat Trailer Connector # C59236. This uses... view full answer...
I'd go with adding a junction box and a 7-way but still using your current light's wiring if it's still good. For that we have the part # HS381-9000 which matches what you need perfectly. It's designed for upgrading a trailer with a 4-way to a 7-way and comes with a junction box and 7-way. view full answer...
Based on the weight of your 2021 R-Pod 195 the Fastway e2 part # FA92-00-0450 would be rated too low and wouldn't be effective. You would need to go about the higher rated # FA92-00-0600 which is rated for 250-600 lbs. Your loaded and unloaded tongue weight would fall within it's range so it would work great either way. view full answer...
I recommend our etrailer Trailer Hitch Receiver # e98869 as the best option for your 2024 Nissan Frontier. The receiver has a matte black finish which gives it a clean factory appearance while the other receivers offered are gloss black which stands out against the rear matte fascia.
The Curt Powered Tail Light Converter # C59236 will allow you to wire in a 4-way flat connector. This is the most commonly used connector on small utility and boat trailers. If you are going to be pulling... view full answer...
I recommend starting off by measuring to see exactly how large of a toolbox that you will need.
I have included a link to all of our A-frame toolboxes for you to take a look at. Two of our largest boxes are the DeeZee Specialty Series Trailer Tongue Toolbox, # DZ91717, and the RC Manufacturing Aluminum A-Frame Trailer Tongue Toolbox, # 350975.
The DeeZee Specialty Series Trailer Tongue Toolbox, # DZ91717, measures 34" long in the back x 20-3/4" long in the front x 19" wide x 22-3/4"... view full answer...
The battery isolation solenoid part # PK5231201 can be installed on your 2016 Nissan Frontier to allow you to only activate your 12 volt power circuit when the key is on. For the center pin of the solenoid you have to find a circuit that only sees power when the the key is. Typically people run a wire up to the fuse box looking for a circuit labeled ignition. Or if you can find a circuit that only sees power when the key is on like the radio that can work too.
In my car I have a couple... view full answer...
Both of the snow chains and snow cables will work great in snow conditions. The difference is the snow chains will give you better grip in more ice conditions because the chain links will bite into the ice where as the snow cables tend to slide over the ice. The snow chains will make a little more noise on dry pavement as compared to the snow cables.
The Pewag Tire Chains, # PWXMR81V, you have referenced is a good choice for snow chains on your 2007 Nissan Frontier 4x4. Another good choice... view full answer...
All you need to install the Curt Venturer brake controller part # C74VV is the correct install harness, part # C51382 which is a confirmed fit.
I attached an install video for this setup in a very similar 2016 Nissan Frontier as well. view full answer...
The length of your winch strap should be at least the winching distance required for loading the boat on the trailer. I would measure from the winch mount on your trailer back to the end of the bunks and go with a strap about that length.
If that distance happens to be exactly the same length as the hull of your boat you could use that length as well.
The part # DL24251 that you referenced is 20 feet in length and is 2 inches wide. I attached a review video for you to check out as well. view full answer...
Yes the Rhino Rack Hi Lift Jack Holder part # RR43101 that you referenced would fit the slots of your Yakima Outpost HD Rack.
Thankfully the roof rack manufacturers all generally use the same channel dimensions so their accessories can fit each other's bars. view full answer...
Check out the picture I attached. It has a diagram that shows how 7-ways are wired up by function. You would need to use that as a guide as your wire colors are non-standard.
Center is reverse, 11:00 position is running light, 9:00 is left stop/turn and 3:00 is right stop/turn. view full answer...
The Thule cargo basket part # TH859XT can fit crossbar spreads that are between 20 inches - 37 inches. Just measure your bars from center to center and make sure that they are in range. Most vehicles are fine.
This rack also offers a 20 inch extension with part # TH8591XT and optional locks, part # TH450400.
. view full answer...
I have a solution for you but there aren't any custom slip over mirrors like the # CM10700 mirrors you were looking at for the 2015 Nissan Frontier.
The K-Source Universal Dual Lens Towing Mirrors # KS3990 will work great for your Frontier. I have a video of these installed on your same vehicle linked for your convenience.
If you prefer a solid mirror opposed to the dual, we offer that K-Source Mirror # KS3891.
Another mounting option to the snap on that I like are the Cipa # 11650... view full answer...
The best way to decide which class cooler you need is to take a look at what you will be towing and where. If you will be towing a light load, less than 2,000 pounds, in flat driving conditions, your vehicle will do fine with a Class I. If you will be towing 6,000 pound load through some hills, I would use the Class III cooler.
I prefer the 8000 and 9000 series. They are built a little heavier and are more resilient. The 7000 series are built a little lighter and can be damaged more easily... view full answer...
I reached out to my contact at BAK and she said that on your 2019 Nissan Frontier, both the MX4 # BAK48506 and the F1 BAK72506 Hard Tonneau Covers will actually rest right above the Utili-Track system on the truck, maintaining full function of the system without any interference. One a lot of the Titan model trucks (especially older models) the covers do need to mount to the rails, which limits their function, but that is not the case with most of the newer Titans and your 2019 Frontier.... view full answer...
Yes, the Rhino Rack roof rack part numbers # RRVA137B-2, feet # RRRLKVA, and custom fit kit # DK374 that you referenced is a confirmed fit for your 2012 Nissan Frontier King Cab with a naked roof.
It uses included custom fit clamps to attach to the door frame of your truck and not a gutter. view full answer...