We have not performed a test fit of the CIPA UTV mirror # CMM37, on a 2012 Arctic Cat 550 GT yet. To determine fit, you will need to measure the diameter of the tubing you want to attach the mirror to. If it is 1-3/4 to 2 inches in diameter then it will fit. I have included a link to the installation instructions for you. view full answer...
I think the adaption can be made for the CIPA UTV Adjustable Side Mirror - Black - Left Hand, # CMM37 and the right hand # CMM38 to fit your 1 inch bars, but that would take some shimming. The 1-3/4 inch round clamp would need a shim that will grip as well as allow pressure for a tight fit.
Another option would be to use the CIPA Handlebar Grip Mount ATV Mirror, # CM-11126 on the top front rail to adjust for that side view mirror adjustment. view full answer...
Since your vehicle has a hitch height of 30" you will need the extensions for the Mad-Ramps Pivoting Ramp System for ATV/UTV Ramps # MR54FR, which is found on our site as the following:
- Mad-Ramps 30" Extensions for Mad-Ramps ATV/UTV Ramp System # MR66DR view full answer...
Yes, Mad-Ramps Pivoting Ramp System for ATV/UTV Ramps - 1,400-lbs # MR54FR will fit your 2019 Honda Ridgeline. It simply attaches to your 2" trailer hitch receiver and allows for safe loading of an ATV, UTV/side by side, or golf cart. The max wheel base is 88", the max width is 60", and the weight capacity is 1,400lbs. I attached a demonstration video for you to check out. view full answer...
I have a solution for you, but we do not have a bench seat cover for a UTV/ATV that is a single piece that covers both parts of the seat because a majority of the seats on these vehicles are either captains chairs or 2 piece bench seats. I recommend using something like the Canine Covers # DE1020BK which is designed for the back seats of cars/trucks, but will act as a one piece cover for your UTV/ATV and provide great protection for your bench seat.
This cover is 60" wide x 19" deep x... view full answer...
We do offer a range of general-purpose ATV/UTV storage accessories such as the Classic Accessories UTV Roll-Cage Organizer for the Polaris RZR. However, we do not offer an equivalent item made specifically for your Teryx. But the link provided will show you all available accessory items for your 2010 Kawasaki Teryx 750.
The link at right will show you all ATV-UTV cargo bag options.
We DO offer some specialized accessories made just for your Teryx, including an all-weather cab enclosure... view full answer...
Yes. The etrailer Horizontal E-Track - Galvanized Steel - 2,000 lbs - 8' Long # e62VR can be driven on without any issue and have a maximum capacity of up to 6000-lbs each(break strength), so they'll be able to handle your ATV/UTV without issue. You can use the Erickson Adjustable Wheel Net with E-Track Fittings - 1,166 lbs # 77314 as your wheel straps if you don't already have some.
I've linked some review videos of these parts for you to have a look at. view full answer...
There is definitely no issue in using 2 sets of the Erickson ATV E-Track Tie-Down Kit # EM09160, one for the back and one for the front, to stabilize your UTV. If you look through the photos that other customers have sent in you can see that some people used one set while others used two. It really is just a matter of preference. view full answer...
I reached out to Mad Ramps about the MAD-MOUNT Wall Mount Brackets for Mad-Ramps Pivoting ATV/UTV Ramps part # MR27DR and they informed me that the brackets are both 36" long x 2-1/2" tall. I have attached a photo below with this as well. view full answer...
We do offer both the ramps and snowmobile kit you're inquiring about, the Mad-Ramps Pivoting Ramp System for ATV/UTV Ramps part # MR54FR and Snowmobile Ramp Kit part # MR69DR which is everything you need to load and secure a snowmobile in your truck bed. view full answer...
The 1,500 pound working load limit (WLL) for the Erickson ATV E-Track Tie-Down Kit # EM09160 referenced in your question does refer to the combined capacity of both straps and chocks. Since your UTV weighs close to 2,000 pounds I recommend using two sets to secure all four of its wheels to the trailer. view full answer...
My contact at Airaid checked the air filters specified for your 2007 Honda TRX680 4-Wheeler and based on his research a better filter option for your ATV is their # AR700-493. This filter has a 3-inch flange to mate with your intake, a base diameter of 6-inches, a top diameter of 4-5/8-inches and a height of 6-inches. If these dimensions match your current filter then this one should be a good fit.
Since these filters are NOT vehicle-specific you'll need to check the measurements of your... view full answer...
I checked with Erickson and even their pictures show just two of the wheels being secured using the ATV E-Track Tie-Down Kit # EM09160. Basically you want to use all 4 of the chocks meaning you would secure 2 wheels. The rear wheels are recommended.
If 1 set does not have the capacity for your UTV then you would need to use an additional set or additional tie downs (see link) to cover the whole weight of the UTV. A set has a safe working load limit of 1,500 pounds and a break strength... view full answer...
The etrailer ATV winch # e98989 has a 3-1/8" x 6-5/8" mounting pattern on the bottom of the winch, so as long as you've got that mounting pattern on your winch plate this will mount directly to your 2020 Polaris Ranger UTV.
If you've got a different mounting plate hole dimension, let me know what you find and I can see if there is a way to make this work for you. view full answer...
When loading a trailer you want to have as much of the weight of the cargo as far forward as possible, otherwise the trailer will sway. In your case I would recommend putting the heavier side by side in the front of the trailer and the ATV behind it.
I attached an article with other tips on towing a trailer for you to check out as well.
If your trailer and cargo weigh more than 50 percent of the total weight I would also recommend you look into a weight distribution system.
The best... view full answer...
The CIPA UTV mirror, # CMM37, has a convex lens meaning that it bows out in the middle providing a wider angle of view. All of the UTV mirrors we carry, see link, have a convex lens. view full answer...
The etrailer 5000-lbs ATV Winch # e98989 comes with a 90-day warranty. I really like the heavy duty capacity for an ATV and the synthetic line is a really great safety feature at this price point. view full answer...
What you could do is install the Curt ATV hitch part # C45006 on your ATV and then use a ball mount with a 4 inch rise like the part # C45070 and then for a 2 inch ball part # 63845. Finally for a hitch pin part # C21500. view full answer...
To choose the correct battery for your 3,500 lb UTV winch you need to see what the cold crank amps rating is for your winch and then make sure the battery is rated that high. For example, the 3,500 lb Bulldog Winch Powersports Series ATV Winch # BDW15013 is rated for 650 CCA (cold crank amps) so your battery needs to be rated for at least 650 CCA. view full answer...
Yes, if you mount the mirror in the orientation pictured, clamp up or down, you will be able to fold the mirror against the UTV to get it out of the way. view full answer...