Hello Mari, thanks for the picture. The Lippert High-Speed Power Stabilizer Jack # LC298707 is a direct replacement for your 369777 rear stabilizer jack. We have confirmed this directly with the folks at Lippert on several occasions so that is definitely what I recommend. view full answer...
The Volkswagen OEM roof racks were made by Thule, Chuck, so since your lock core says 014 the correct replacement key would be the part number # THKEYN014. view full answer...
Hi Jim,
If your Fogatti RV Tankless Water Heater # LSB64FR is turning on but not sensing when water is passing through then you could either have a bad water flow sensor or there's the possibility that you have a shut off valve somewhere leading to the unit that could be turned off. A lot of RV's will install quarter-turn valves to separate the water heater from the rest of the plumbing so that they can run anti-freeze through the lines for winter. I recommend checking that your unit... view full answer...
Past customers have told us the AL-KO 8460 uses inner bearing 25580 and outer bearing 15123, which would make the Timken Bearing Kit # TMK82VR the correct replacement bearing kit for that hub. If you are looking to replace the hub entirely the correct hub will be the following:
Dexter Trailer Hub and Drum Assembly - 5,200-lb and 6,000-lb Axles - 6 on 5-1/2 - Pre Greased # 8-201-9UC3-EZ view full answer...
Craig, you can add a heat strip with # ACMHD to the Advent Air RV Air Conditioner # ACM150, but this is just designed to take the "bite" out of the air not heat your trailer - you're still going to want to rely on your furnace to heat your trailer. view full answer...
I have seen both the Steel # 9106 and Aluminum # RV-626-062 Pop-Up Vents used in a open position to allow the air to blow into the trailer while driving. While I do not see the manufacturer having any kind of speed rating on these I would be hesitant to the speed or having them opening forward depending on the material you are mounting it to. Since some trailers only use fiberglass shells I would not find that material secure enough to hold the vent open while driving. But if you have a... view full answer...
Jason, it looks like for a Karrite Expedition cargo box, you're going to want the Replacement Lock Core and Key for SportRack Explorer Cargo Box # SR03807 for a replacement. view full answer...
Since your 2020 Acura RDX did not come with trailer wiring you are going to need the T-One Vehicle Wiring Harness # 118804. Then you will be able to connect and pull your trailer with a Ball Mount # DT49MR.
For your utility trailer if you are looking to install new Tail Lights # M844 & # M844L you might consider changing the Wiring # A25W2GWB harness as well if it is damaged. We also have the Fender Light # MCL180ARB if your trailer uses these style lights. view full answer...
The only replacement brakes we have that fit the same AL-KO brake mounting pattern of the K23-528-00 & K23-529-00 brakes are the Kodiak Disc Brake Kit # KD94FR. The AL-KO axles in this capacity used a unique 5 bolt mounting flange which we only carry in the disc brake kit. The Kit # AKEBRK-8 you found only has a 4 bolt mounting pattern. view full answer...
The main reasons the Timbren Axle-Less Trailer Suspension # ASR35HDS02 is better for off road applications is it uses the larger spindle which is going to be stronger and less likely to become damaged when your axle falls off a ledge or into a hole. Also the spindle sits further from the suspension allowing for a wider tire without large offset wheels.
Some would assume because the Kit # ASR3500S06 has a 4" lift that it would be better off-road but it has the lighter spindle and the hub... view full answer...
Tom, the Kodiak Disc Brakes # KOD69FR you're looking at will work great as a replacement. You're probably already aware that TDE is no longer a company that's in business, so a full replacement is going to be your only choice.
This brake kit has a 1 piece hub-and-rotor assembly which helps reduce the chance of uneven rotor wear and uses a vented design to dissipate heat faster and prevent premature brake pad wear. view full answer...
If you need a replacement tongue that isn't something that we offer. You can see if the manufacturer offers a replacement since it looks like it folds. If they don't have a replacement you would have to take it to a shop that could add a new tongue along with a coupler hinge kit like # FHDPB330301 to keep the folding functionality.
I can't do much with the VIN but it does look like that has a Dexter A-60 in the end of it based on the pictures I found. If you're able to remove the actuator... view full answer...
Since the Reese 5th Wheel Trailer Hitch 30051 fits into industry standard rails which is the same pattern Curt uses for their rail kits you are able to use them Andre. For your 2015 Ford F-150 you would need the Fifth Wheel Installation Kit # C38ZV which includes the above bed rails and custom fit below bed mounting brackets.
The Hopkins Wiring # 41157 will allow you to tee into the bumper 7-way and add another 7-way connector in your bed. This protects both the trailer wiring and bumper... view full answer...
The T-60379 is the same as the RetraxONE XR Hard Tonneau Cover # RTX72GR. The correct rails for this tonneau cover are the Replacement Side Rails for Retrax XR Series T-Slot Accessory Hard Tonneau Covers # RTX75QR. view full answer...
Yes, you can use the # TLL160RK on your 2019 Palomino Solaire 268BHSK without having to modify the rear of the trailer. These are surface mount lights so they can sit where the old lights were located. If you want an exact replacement it looks like it originally came with the # RVSTLB61 and # RVSTLB60. view full answer...
We probably do have replacement bearings for your dolly but we don't know what they are so you would need to pull the hubs off of the dolly spindle and get the bearing numbers off of what's in there. view full answer...
Hi Vincent,
We do have replacement hardware for the Curt Trailer Hitch Receiver # C13363 for a Jeep Compass; what you will need is the following:
- Replacement Hardware Kit for Trailer Hitches # RHK
All you need to do is click # RHK, enter "C13363" in the "Hitch Item Number" box and you're set. view full answer...
There are a couple of different trim kits from Furrion but it sounds like you have the Kit # FMSM09SSTK which presses onto the brackets that attach to the microwave. This trim pulls off the front to gain access to the screws which hold the microwave in place. A Trim Wedge Kit # PTW80647 would aid in the removal. You can see in the video I linked near the bottom of the page how the kit presses into place and is held in the tabs.
They also offer trim kits which are held in place with screws... view full answer...