I do have a way for you to install the Hopkins Endurance 5th Wheel/Gooseneck 90-Degree Wiring Harness # 41157 in line of the Hopkins Plug-In Simple Vehicle Wiring Harness # HM43385 but it does not look like it will plug and play as the one I see has the wiring hard wired into the 7-way and not on a removable connector. To remedy this you can cut the Extension # C86DR in half and cut the wiring on the Hopkins Harness # HM43385 and then wire them together. Then you would be able to connect... view full answer...
You found all the correct components for your 2021 Subaru Outback Premium with the factory raised rails. The Basket # Y07138, will mount to the Round Crossbars # Y00408. The crossbars then mount to the Skyline Towers # Y53TR using the Adapters # Y03536. And the towers will connect with the Landing Pads # Y46VR.
I recommend getting the Locks # Y07208 to secure the rack and basket to your roof. view full answer...
Adam, we don't have any air springs unfortunately for your 2006 Workhorse W42, but we do have the Timbren Rear Suspension Enhancement System # TGMRP30.
These are hollow rubber springs that sit above the rear axle, has up to 6,000 lbs of capacity, and requires no drilling for installation. view full answer...
Hello Slavik, we can definitely set you up with a hitch and wiring for your 2020 Honda CR-V Hybrid. For a hitch I recommend the etrailer Class 3 Hitch # e98848. This has a 2" receiver and is capable of towing up to 3,500 lbs or 525 lbs of tongue weight. It is important to note that the hitch may interfere with the Hands-free Liftgate sensors and functionality may be very limited or possibly lost.
For a wiring harness I recommend the Curt T-Connector # C56370. This will be a very easy plug-and-play... view full answer...
Hello Jim. The Stealth Hitch # 391SUCT18 is not verified for the 2022 Subaru Crosstrek because the manufacturer specifies it will only for the 2018-2021 Crosstrek models. Unfortunately, Stealth Hitch does not make a hitch for the 2022 - present Subaru Crosstrek.
We actually had a few reps from Stealth Hitch here a couple weeks ago and I brought this up. We get a lot of Subaru owners asking us about stealth hitches and I was curious why they stopped making hitches for a lot of Subaru models... view full answer...
There is no specific torque setting for the axle nut with the # AKIHUB-440-2-G-EZ-1K. Check out the installation video below starting at the 13 minute mark. The hub is overtightened at first to make sure everything is seated. Then he backs off the castle nut until it is loose. After that, tighten it back until you get a little bit of pressure and make sure there is no play. Then you will check your holes for your cotter pin. For the lug nuts you're going to have 8-14" wheels and this has... view full answer...
Yes, we do have the instructions for the etrailer Hitch item # e75ZR that fits your 2024 Toyota Highlander. We also have an installation video we did on the 2023 model year. I have linked both below:
You will need the following tools to get it set up:
RATCHET
TORQUE WRENCH
10mm SOCKET
12mm SOCKET
17mm SOCKET
19mm SOCKET
6" EXTENSION
SCREW DRIVER
ROTARY TOOL (OPTIONAL)
SAFETY GLASSES view full answer...
The base of the Demco Recon # DM8550045 drops onto the 2-5/16" gooseneck ball then a pin is inserted into the tapered down section of the ball. Then there is a coupler nut above this that gets tightened down to hold tight on the gooseneck ball. You can see these steps in the installation instructions I have linked near the bottom of this page. view full answer...
Hey Goran,
When the bolt is threaded into the rivnut and you tighten it down it start to bulge out as it bolt compresses it against the inside of the trailer frame, locking it into place. If the hole you drilled is slightly too large then the splines on the rivnut won't be able to grip the frame and it will spin as you try to tighten the bolt. The hole should be exactly 11/16" in diameter for a snug fit. If your holes are slightly larger you can pick up a rivnut setting tool at your local... view full answer...
The Ride-Rite Red Label Extreme Duty Air Helper Springs # F56ZR is the kit specifically made by Firestone for your 2020 International CV series truck. These springs will provide up to 7,500lbs of support to your factory leaf springs. I have linked the installation instructions near the bottom of the page so you can see what all is involved for the installation.
The Firestone Air Command Heavy Duty Air Compressor # F2097 will allow you to adjust the air pressure in the air springs from the cab. view full answer...
Hey Roger, I attached a link to the install instructions for the Hollywood Racks RV Rider Bike rack part # HLY64FR that you have on this page as well as attached a review video that help visualize how it's used/installed as well. view full answer...
Hey Robert, thanks for reaching out!
You shouldn't have any issues fitting the B&W Heavy-Duty Trailer Hitch Receiver # BWHDRH25122 on your 1992 Ford F-150, but since we haven't performed this installation yet, I recommend checking out the linked video of this hitch on a 1988 F-250 so you can compare it to what you have.
We don't have insight into what the dual tank system looks like on your truck, and while it may not be necessary to remove your spare tire for the installation, it will... view full answer...
Hey Rob, I would go with the Curt trailer hitch part # C92WR for your 2023 Volvo XC60 Recharge which like you said is going to have an easier install and also we have found they have a higher quality consistently. view full answer...
Hey Rick, you are correct the blue brake output wire would also need to be connected to terminal 1 for the Roadmaster Brake-Lite Relay Kit for Towed Vehicles # RM-88400. view full answer...
We are only going to have a 94" # 8327864 and 95" # 8327834 width for a 7,000lb axle beam. If you are wanting a solid axle beam like this the same width as your F-250 it would have to be special ordered from a local dealer. Otherwise we do offer the Timbren Axle-Less Trailer Suspension # TASR7KS01 which will allow you to customize the width of the axle based on the mounts. Each hub face will sit 6-1/4" from the frame rail it is mounted to. This system has its own suspension setup built... view full answer...
Thanks for your continued support Michael! I drive out to Kansas a few times a year myself and I definitely know the drive you're talking about.
Your Thule Quest TH846 was actually replaced by the Thule Outbound Rooftop Cargo Bag # TH868 and they install the same way. They have the front and rear straps for crossbars, but Thule also points out that the side anchoring rings can be used if the only anchoring option for your vehicle is the side rails (see attached clip of instructions).
Thule... view full answer...
Per the linked installation instructions which you can click below the torque is 86 ft-lbs for the 12mm hardware when installing the etrailer Trailer Hitch Receiver # e75ZR on the 2023 Toyota Highlander. view full answer...
Hey Robert,
The Thule TracRac SR Sliding Truck Bed Ladder Rack # TH43002XT-606 mounts to the stake pockets in the bedrails. If your Titan doesn't have stake pockets then it will just require some drilling in order to install. view full answer...
Unfortunately no, Don. Since the Kuat Ibex Customizable Overland Truck Bed Rack # KU56ZR uses bed rail clamps to install that would require the truck bed to be open and not covered by anything. view full answer...
Usually our pictures show all of the hardware that come with the hitch. For some reason the # 31352 pictures only show the two bolts, nuts, and spacers. You actually get six of each as listed in the instructions which I have attached below. You do not need to supply your own bolts for installation. view full answer...