You'll have two options when it comes to a two panel system:
Option 1: Go Power Overlander Solar Charging System with Digital Solar Controller # GP39MR. These panels have a hard frame and would require you to drill into the roof of your trailer. They are 59-1/8" L x 26-5/16" W and provide up to 380 watts.
Option 2: Go Power Solar Flex Charging System with Digital Solar Controller # 34272628. These panels have a soft, flexible base to fit curved surfaces and can be glued to the roof instead... view full answer...
To add a hitch to your 2019 Lance 2395 Travel Trailer, I recommend the Curt Adjustable Width Trailer Hitch Receiver for RVs item # 13703. This hitch fits frames that measure from 22" wide up to 72" wide. This hitch works on box frames, C-channel frames, or I-beam frames thanks to the bracket design.
The Curt Trailer Hitch item # 13703 has a 2" receiver with a towing capacity of 3,500 lbs and a tongue weight capacity of 350 lbs. This will work great for a bike rack.
I've linked an installation... view full answer...
We definitely have a couple options available to carry your generator, though it will depend on the weight of said generator.
First, the Stromberg Carlson Trailer Tray Cargo Carrier # CC-255 will install on the A-Frame at the front of the trailer. This has a 300 pound capacity and being 29 inches tall, it will typically clear any accessory or propane tank. The only downside is it can get fairly tall making it difficult to get the generator up onto the carrier.
I tend to like the bumper... view full answer...
To install the Ventline Ventadome Trailer Roof Vent, # V2092SP-28 in the clamp-in installation option, you will need the four (4) VB0492 clips that are purchased separately. This is not an item that we carry. Even though the manufacturer has this as an installation option, we highly recommend using the more common and proven method of using screws. We carry the Roof Vent Installation Kit, # 344270KITW that contains sealant, Butyl tape and screws. And we have a very thorough installation... view full answer...
Crossbars of that length are not available; the longest possible crossbars are the 79 inch Rhino-Rack Vortex Aero Crossbars # RRVA200B-2. view full answer...
According to my available specs on the discontinued Kuat NV, the weight capacity on that rack is 60 pounds per bike. This is the same capacity as the 2.0 version.
However, I strongly recommend the newer 2.0 version # NV22G over the previous model. This is because the 2.0 has the foot-release lever and can accommodate wider bike tires. Additionally, the arms that attach to the bikes were redesigned to allow them to glide more smoothly. Another great addition is that the locking hitch pin... view full answer...
Given the wheel bolt pattern and the 8-247 that's cast into your existing brake drums, you have a 3500 lb axle. Assuming you have E-Z Lube spindles with the grease zerks in the end, you'd want to use the
# AKHD-545-35-EZ-K hub/drums you looked at. If you have standard spindles, use # 84546UC3.
At the very least, you'd want to replace your brake magnets, if they've got grooves worn into them as they won't get a good contact with the new drums for effective braking. If your brake assemblies... view full answer...
Weight distribution shanks are essentially universal so long as they have the proper hole spacing of 1-1/4 inches apart for most systems, including your Curt TruTrack Weight Distribution System # C17499.
That was a long way of just saying yes, the Curt TruTrack system is compatible with the shank you asked about:
- Curt Welded Weight Distribution Shank # C17123 view full answer...
You'd want to go with a cover that is slightly longer than what your camper is so since yours is 15-1/2 feet in length the Camco UltraGuard part # CAM45771 would be what you'd need as it fits up to 16-1/2 feet in length. view full answer...
For your 2001 Ford Pleasure Way Excel TB on a Ford E-350 Chassis you'll need the Roadmaster Rear Anti-Sway Bar # 1139-178. For the front you would need the Roadmaster Front Anti-Sway Bar # RM-1139-115. view full answer...
Ok, we have some options for you, and I should note that bike racks do need to be approved by their manufacturer for the use on the back of travel trailers like your 2021 Lance 2185. There aren't any travel trailer approved racks for a 1-1/4 inch hitch, but from what I could see it does look like this trailer has a bumper. So what you can do to add bikes in the rear of the trailer, so long as the bumper is 4 to 4-1/2 inches tall, is add a Swagman rack:
- Swagman Traveler XC2 Bike Rack... view full answer...
The length I'm seeing for a 2018 Lance 650 truck bed camper is 15'6" so the Camco UltraGuard Slide-In Camper Cover - 16-1/2' Long # CAM45771 would be closest fit at 16-1/2'. The extra foot of material should make getting the cover in place easier and the excess can be tucked and strapped down with the integrated straps. view full answer...
The # PF281007 Replacement Spray Head for Phoenix Faucets Hybrid Pull Out Kitchen Faucets is made for a Phoenix faucet and will not fit on the Dehco. Dehco does not have repair kits or replacement parts for their faucets.
I recommend replacing the faucet entirely. Since you were already looking at the replacement spray head for the # PF231441 Phoenix Faucets Hybrid RV Kitchen Faucet w/ Pull Out Spout, I believe this will work well for you. It has a plastic underbody, metal powder coated... view full answer...
The # FV807357 Fan-Tastic Vent Roof Vent Assembly Upgrade Kit will work for your 2019 Lance 2185 Travel Trailer if the opening meets the requirements. In order to install this vent, you must have a 14-1/4" x 14-1/4" opening approximately in the trailer's roof and ceiling and the roof can be no more than 4" thick.
These are standard dimensions for a vent opening. If this does not work for you please send measurements and I will do my best to find a solution.
I have attached a review of... view full answer...
The Fastway ONEstep wheel chock, part # FA84-00-4000 isn't a trailer specific item. As long as the spacing between the tires is between 16-24 inches as shown in the provided photo, the # FA84-00-4000 chock will work great for you.
I've linked to a demonstration video showing how the chock works. view full answer...
The Replacement Jack Crank Hub Cap for HappiJac Camper Jack System # LC34HD that you referenced is sold individually. If you needed 4 you'd need to order a quantity of 4. view full answer...
I think I have the answer. I confirmed with Lets Go Aero that the Bikewing 2 B01311 should not be used on a travel trailer. We do not recommend using 1-1/4 inch receivers on travel trailers because a 1-1/4 inch bike rack/hitch combination is not very secure on a travel trailer shank with the added torque experienced at the end of a trailer during travel (especially with added bike weight).
However, there are many 2-inch hitch/bike rack combinations that are guaranteed to get the job done... view full answer...
The correct sized cover for your 16'8" Lance 855 truck bed camper is the Camco UltraGuard Slide-In Camper Cover # CAM45770 which is designed to fit truck bed campers up to 18'2" long.
This has self-adjusting hold-down straps so you can fit it better to the body of your camper and not have as much slack. view full answer...
Yes, the Trailer Valet XL Mounting Bracket # TVXLMB is able to mount on a 2 x 6 trailer frame, however it is only compatible with the Trailer Valet XL Trailer Dolly with Chain Drive - 2-5/16" Hitch Ball # TVXL25 or 2" Hitch Ball # TVXL2.
If you do have a 2 x 6 frame, however, you will not need a larger bracket to use the Trailer Valet JXS Trailer Jack w/ Footplate and Drill Powered Option - Side Mount - Sidewind - 5K # TV64FR.
The JXS Jack # TV64FR comes with a large mounting bracket... view full answer...
The TorkLIft # TLA8102 will be a good fit for your trailer if the "Entry Height" is between 18-1/2" and 28" and the Mounting Bracket width is no more than 25-1/2".
To determine Entry Height, measure from the ground up to the top of the the bracket frame that held the old steps. The product page has a picture showing how to measure.
Then, determine the "Mounting Bracket Width". If your mounting bracket is no more than 25-1/2" wide then the # TLA8102 is a fit. If you have different measurements... view full answer...