If I'm understanding you correctly, the MORryde StepAbove RV Steps # MR68RR is 8.3" deep when in the upright position.
Based off of the measurements you took of your 2007 Keystone Montana 2955RL, the MORryde StepAbove RV Steps # MR68RR should work great for you. view full answer...
The Andersen Ultimate Connection 5th Wheel Trailer Hitch # AM3200 is compatible with a Trailair Air Ride 5th Wheel Pin Box # LC158778. That being said Andersen states you need to use their flex lockout kit because there is too much movement in the pivot of the Flex cushion for that hitch without locking it out, which would essentially negate the benefit the pin box would give you. view full answer...
The specs I'm seeing for your 2006 Keystone Raptor Toy Hauler 5th Wheel show 37'-7" in length so you'll want to go one size up from the ADCO AquaShed RV Cover # 290-52256 to the Adco SFS AquaShed RV Cover for 5th Wheel Toy Hauler - Up to 40' Long - Gray Item # 290-52257. You'll want to have a little extra slack to ensure you can fully cover your Toy Hauler and you'll be able to tighten up the excess with the straps and buckles. view full answer...
Hello Ms. Hames -
I would really like to recommend a USA-made 2-bike hanging rack, but I need a bit more information. Do you have the make and model of your vehicle?
Thanks so much -
Bob
etrailer.com view full answer...
The previous generations of the Correct Track had some issues with brackets bending but the current generations like the single axle part # LC87120 and tandem axle # RR23QX have had all of that addressed and fixed. view full answer...
As your 2005 Keystone Raptor 3212DS is a triple axle you will need a kit like the MORryde Rubber Equalizers for Triple Axle Trailers # MR39ZR. The Lippert Road Armor # LC696740 will only fit on tandem axle trailers. I do recommend also installing the Wet Bolt Kit # MR86ZR with the equalizers. This will allow the suspension to move more freely.
While the equalizers and wet bolts above will allow the suspension to absorb some road shock, adding shocks will still improve the overall ride... view full answer...
The 901 bulb shares the same T-5 wedge base as the 921 Bulb # VA0415-00. You will want to verify with the LED bulb manufacturer to ensure the bulb is compatible to replace your 901 bulb as there may be a issue with the overall size of the bulb itself. view full answer...
As long as your 2005 Cougar 254 5th wheel trailer has a door width no smaller than 26" and your threshold height is in the range of 27" - 36" from the ground then the SolidStep Manual Fold-Down Steps # LC791572 is a great solution for you! If your 5th wheel doesn't fall in either of the specs listed above let me know what you have and I can help you choose the correct steps. view full answer...
The replacement hinge part # LC198295 is what you are looking for as it's not a friction hinge that stops the door from moving and is correct size for your 2022 Keystone Cougar. view full answer...
With the research I did, I found that your 2021 Keystone Cougar 364 BHL has a length of 39' 2". The Classic Accessories PolyPRO 3 Deluxe Extra Tall 5th Wheel or Toy Hauler Cover - XT Model 7
# CA80-300-203101-RT would be a little too large.
I recommend the Classic Accessories PolyPro III Deluxe Extra Tall 5th Wheel Cover - Model 6 37-41'
# 052963750638 because it fits trailers from 37' to 41' and will give you a more snug fit on your trailer. view full answer...
The Roadmaster Dual Hitch Receiver Adapter for Tow Bars # RM-077-2 is not recommend for use with a trailer so you'd be voiding any warranty towing your motorcycle trailer with it. It also only has a 400lb tongue weight so you'd need to make sure that the weight of the bike rack, bike, and tongue weight from the trailer doesn't exceed 400lbs. There isn't a 2-1/2" version of this adapter but a stacked receiver might be the better option for you.
The Gen-Y Phantom X Adjustable 2-Ball Mount... view full answer...
Thanks for all that info, that was awesome. And for your 2019 Keystone Cougar 315RLS with a 5,200 lb axle, hub with 6 on 5-1/2" bolt pattern, and Nev-R-Adjust electric brakes, here is exactly what you need:
- Dexter Trailer Hub and Drum Assembly # K08-201-98
- Dexter Nev-R-Adjust Electric Trailer Brake Kit # 23-458-459
- Mounting Bolts and Hardware for 12" Brake Assemblies # BRKH12 view full answer...
If you have a Lippert 1621 wing set on your 2004 Keystone Cougar 5th Wheel which is the most common then I can confirm the Lippert 1621 5th Wheel Pin Box part # LC1191191 will fit and work well on your trailer. Please don't pay any attention to the note on the product page, "NOT CONFIRMED TO FIT 2004 Keystone Cougar Fifth Wheel". view full answer...
Yes, the MORryde Cushioned 5th Wheel Pin Box # MR74VR is the correct replacement for your 2019 Keystone Cougar 338RLK. Your Cougar has a GVWR of 12,490lbs which falls into the 11,500lbs to 14,000lbs the MORryde is rated for. And since you already know you have the 1621 bolt pattern it will have the same bolt pattern. view full answer...
I do have a ton of different bulb seals for you to choose from but we don't have any way of knowing what any one particular trailer uses. That said, all you really need to do is look how the existing attaches; flange mount, track mount, c-channel mount, stick-on etc. Then you can choose one from the list attached below after you confirm the length you need as well.
The Rubber Bulb Seal for RV Slide Out part # SR69FR for example mounts in a 3/16" track and measures 15' long. view full answer...
In regards to the Solera Slide Topper Awnings, the overall width is actually adjustable so I don't have an exact figure for you. This is because you can slide the hex extension rod in and out of the support arm bracket. The correct way to choose a Solera Slide Topper Awning is to measure from the outside edge of each flange on your slide out. The support arm will then stick out a minimum of 3" past the outside edge of each flange. I have attached a photo for you which shows this.
If the... view full answer...
The Valterra Lockable Dual RV Water Inlets # A01-2000VP is very similar in size but without knowing the actual cutout hole dimensions it's not possible to know if you'll need to make modifications. This dual inlet box requires a 5-7/8" wide x 4-3/4" tall cutout hole.
Worst case scenario you would have to trim the cutout hole a bit larger to fit this new inlet box in place. You'll want to use butyl tape # AL28FJ on the mounting flange and non-sag sealant # 344270341437-1 around the outer... view full answer...
The part numbers you mentioned are our part # FR43PR for the Furrion Chill HE controller and the # FR86PR for the Chill HE RV AC unit. These two are compatible. view full answer...
I do have an option for you but we do not carry specific Lippert brand axles like the serial number LC152-SB-92-74.5-NOSP-L-65516DR-7225. According to my research it is a 5,200 lb Lippert brand axle that measures 92" hub face to hub face and 74.5" spring center to spring center. We currently do not carry an axle with these measurements.
Your best option is to use Timbren Axle-Less Suspension part # TASR5200S03 which will still be a 5,200 lb capacity and take the same bearings as your... view full answer...