You will need these three toppers.
The Solera RV Slide-Out Awning - 7'7" Wide - 48" Projection - Black # LCV000168106.
The Solera RV Slide-Out Awning - 12'7" Wide - 48" Projection - Black # LCV000165061.
Solera RV Slide-Out Awning - 13'7" Wide - 48" Projection - Black # LCV000168110.
These will give you the 2-1/2 inches of overhang on each end that is recommended by the manufacturer. view full answer...
SnapPads like part # SP54FR4 are not able to be used under the Stromberg Carlson Base Pad Extreme # SC33VR as they wouldn't properly fit the base of the base pads. The base pads can be used under the SnapPads to help clear up large gaps though.
You can not use the # SC33VR upside down either as this work completely against it's weight distributing design. This would also most likely have the jacks come down on the inner supports of the base which would end up damaging them. view full answer...
As long as the measurements you provided are taken from the outside of the flange to the outside of the flange on your slide out(s) then then following are the correct white slide out toppers for your travel trailer.
127-5/16": Solera RV Slide-Out Awning # LCV000163295
144-3/4": Solera RV Slide-Out Awning # LCV000163298
These are both white slide outs and come with the brackets, hardware, and awning rail needed for installation. view full answer...
For your Fan-Tastic Vent Roof Vent w/ 12V Fan and Remote # FV807350, I first recommend verifying that you have new, fresh batteries in your remote.
If you've verified that your batteries are indeed new, and in working order, then I recommend to check the 4 amp slow burning fuse and see if it has been blown or not.
You can access this fuse by pushing up on the black cap and 1/4 turn once left. The fuses must be out for a minimum of 90 seconds before replacing.
If it is blown, you can... view full answer...
In order to tow a trailer with a 2019 Ram 1500 Classic you'll need a trailer hitch, trailer wiring harness, and ball mount/hitch ball. For a trailer hitch, I recommend the etrailer Trailer Hitch Receiver part # e98852 which offers an easy bolt-on install. For a trailer wiring harness, I recommend the 7- and 4-Pole Trailer Connector Socket part # HM40975 which is also plug-in-play and installs into a factory cutout in the bumper.
Then for a ball mount/hitch ball, measuring would be the... view full answer...
We do have the correct SnapPad's that you need but the SnapPad XTRA Jack Pads for Lippert Leveling Systems w/ 5-1/2" Square Jack Feet # SN68FR would not be the correct ones if you have 6" feet.
The correct SnapPads would be the SnapPad XTRA Jack Pads for Lippert Leveling Systems w/ 6" Square Jack Feet # SN99FR.
The SnapPad # SN99FR are for 5-3/4" to 6" square pads so they will work for your feet measuring close 6". view full answer...
Weight distribution shanks typically have industry standard bolt hole spacing of 1-1/4 inches on center like the
Curt # C17131 shank you'd looked at. If your Eaz Lift weight distribution head has the same bolt spacing, the 2-1/2 inch hitch compatible shank will work perfectly for you. I've linked to a product description video featuring the Curt # C17131 weight distribution shank. view full answer...
The Roadmaster Comfort Ride Shock Absorbers for Tandem Axle Trailers # RM-2460 is designed to fit 3 inch diameter axles, and based on my research, this is the size of axle that is on your 2018 Jayco Eagle HT travel trailer.
You will need to verify that with a quick measurement just to be sure, but if you do in fact have 3 inch diameter axles then you can absolutely use the Roadmaster Comfort Ride Shock Absorbers for Tandem Axle Trailers # RM-2460.
Once installed these will give you a... view full answer...
The maximum forward distance of the 16k Reese Goose Box 5th-Wheel-to-Gooseneck Air Ride Coupler Adapter - Lippert 1716 # RP94716-61301 is 7-1/2 inches. It will be the same when it is either inflated or deflated and it won't move even when you are traveling. view full answer...
What you really want to do when choosing a weight distribution system is try to get as choose to the middle of the systems capacity as possible. The typical tongue weight of a trailer will be anywhere from 10% to 15% of the total weight of the trailer.
With that being said, I do suggest going with the Equal-i-zer # EQ64FR. This will have the minimum tongue weight of 1,200 pounds and the maximum tongue weight of 1,600 pounds. I should not that with the minimum tongue weight being 1,200... view full answer...
I would try unplugging the touch panel part # LC74FR and plugging it back in to see if that clears out the light. My guess is it just has a weird internal bug from being on the charger for so long and that will clear it up. view full answer...
I have exactly what you are looking for. My research tells me that the RadRover Step-Thru weighs about 71lbs and the RadRunner weighs about 65lbs. Your best option is the Swagman E-Spec Bike Rack for 2 Electric Bikes - 2" Hitches - Frame Mount # S94FR. This has a weight capacity of 70lbs per bike and is rated for use with travel trailers. If your bikes weigh slightly over 70lbs then you will want to remove the battery back to reduce the weight. Keyed-alike locks are included to deter theft... view full answer...
The white color version of the Replacement Short Arm Assembly for RV Awnings - 63" Long - Black # LC404523 is available with part # LC97UD. view full answer...
The correct glass shade replacement for the # 277-000422 is the part # 277-000431.
In order to remove the outer globe on the Gustafson RV LED Pendant Light part # 277-000422 you need to loosen the wiring from the bottom of the base and feed the socket through the glass. The bulb is actually not replaceable. view full answer...
When I took a look at the specs of your 2019 Jayco Eagle 332CBOK, it said the trailer had a GVWR of 12,000 lbs, and based on that we know your tongue weight is going to be in the 1,500 lb range. With that in mind, there is one option for an Equal-i-zer weight distribution hitch with the needed capacity for trailer:
- Equal-i-zer Weight Distribution System with 4-Point Sway Control # EQ64FR
This system is designed to work with trailers that have a total loaded tongue weight between 1,200... view full answer...
The Andersen Ultimate Connection 5th Wheel Trailer Hitch # AM3200 is compatible with your 2015 Ram 2500 with puck system when using a rail adapter. For your truck, I recommend the Demco 5th Wheel Rail Adapter for Ram OEM 5th Wheel Towing Prep Package # DM6099 or the Reese 5th Wheel Rail Adapter for Ram OEM 5th Wheel Towing Prep Package # RP30154 for that adapter.
You may also want to consider adding the Bargman wiring harness # 50-97-410 to add a 2nd 7-way wiring connection to the bed... view full answer...
The longest sewer valve cable we offer is 10', the Valterra Cable with Valve Handle part # TC120PB which you then need to combine with the Valterra Waste Valve for RV Gray Water Tank part # T1001PBC since you can't use Valterra cables with LaSalle Bristol waste valves. I checked with Valterra and this is the longest option they offer. Therefore, it looks like you'll have to reconfigure your setup since they don't make exactly what you're looking for. view full answer...
Per Viair their RV Winterizing Kit # VA27WR can only be used with the following compressor systems.
Viair Automatic RV Portable Air Compressor for Class C RVs - 150 psi - 2.30 cfm # VA87WR
Viair Automatic RV Portable Air Compressor for Class A RVs - 150 psi - 1.80 cfm # VA59WR
Viair BaseCamp Heavy Duty OnBoard Air Compressor with 2 Gallon Tank - 150 psi - 2.62 cfm # VA26WR
Viair Interstate Constant Duty Onboard Air Compressor with 1.5 Gallon Tank - 200 psi - 1.86 cfm # VA58WR
Viair does... view full answer...
The shackle straps included in the Lippert Tandem Axle Equa-Flex AP Kit - Wet Bolts - 3-1/8" Long Shackles # LC64FR you mentioned are 3-1/8" center to center and 4-3/8" overall length as shown in included diagram.
Using the longer shackle straps will raise your trailer, but I recommend replacing your current hangers with longer ones as it will give you an even lift on each side of the trailer. You will want to measure your current hangers to see how long they are, and then select the... view full answer...
Go To Results