The Tekonsha Prodigy RF you'd looked at, part # TK94FR would work well for you. The controller would mount directly to your trailer tongue, the trailer's 7-way would plug into the unit, and the unit itself would plug directly into the 7-way on your vehicle. The controller uses a remote that plugs into the 12-volt outlet on your dash.
As long as the 7-way on the vehicle has a functional 12v feed, the controller would work great for you.
You needn't worry about this one coming loose. I've... view full answer...
With there already being a factory hitch installed on your 2010 Ford F-150, we do have an option to up the tongue weight capacity. That being said, there are no Class V hitches that we have available for your vehicle, so this will be a Class IV hitch as well.
The TorkLift SuperHitch # TLF1005H is rated up to 1,500 pounds when used with a weight distribution system. The only problem with this hitch is that it sits under the factory hitch, which will affect how the weight distribution hitch... view full answer...
Yes we have everything you need to flat tow your 2021 Ford Escape Hybrid. To begin with you will need a base plate kit, I recommend the Roadmaster Direct-Connect Base Plate Kit with Removable Arms, # RM39FR. This will mate to the Roadmaster Falcon All Terrain, Non-Binding Tow Bar, # RM-522; this is a non-binding type allowing you to unhook your tow vehicle easily and quickly even if you are parked on un-even ground.
For safety cables and wiring I suggest staying with the Roadmaster brand... view full answer...
I have an option for you, but there is not a custom fit trailer hitch receiver confirmed to fit your 1990 Ford Conquest 24' Class C Camper. The Draw-Tite # 75703 is designed to fit the passenger van versions of your 1990 Ford Van, but the frame is different for the Cab and Chassis models used for the campers.
Instead you may be able to install a universal hitch like the Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver - Weld On - Class V - 2" # 41990-07 with 7" tall mounting brackets... view full answer...
For determining the proper size Solera slide-out awning, you need to measure the total width of your slide room from the outside including the flange and then add a minimum of 5" (2-1/2" each for the left/right side overhang). You can have greater than 2-1/2" overhang if you want, but it is suggested that you do not go any less. If you have done so with resulting measurement of 96" you need an awning no less than 101". You can go beyond the overhang of 2.5" each side if you choose, no worries.... view full answer...
In regards to choosing the correct valve stem extenders, this will really come down to your specific application so it would be hard for me to help you pick out a set. The Wheel Masters Tire Pressure Valve Extenders part # WM8029 usually work well on the front and the Wheel Masters 2-Hose Inflation Kit part # WM8005 is a good option for the rear. These will both work great with screw-on cap style TPMS. view full answer...
The Ultra-Fab Stabilizer # UF39-941705, though technically not designed to lift the trailer, per se, will still provide some lift when leveling the trailer out. That being said, these are rated to 6,000 pounds of leveling lift, but as a general rule, this style of stabilizer should not be used to lift a trailer to the point of changing a tire or something to that affect. view full answer...
For installing the Curt Trailer Hitch Receiver # C13195 we do not have installers that we recommend. I have attached below a video showing the installation on your 2016 Kia Sorento so that you can decide if you would like to install the hitch yourself as there is no drilling required and the hitch can be installed with minimal tools required.
If you still wish to have it installed by a professional I recommend going to Curt's website and locating their preferred installers in your area.... view full answer...
I would be happy to help!
The Curt Trailer Hitch Receiver # C11276 is confirmed to fit your 2011 Toyota Prius and has a 200lb tongue weight rating and 2000lb trailer weight rating so you will need to make sure your trailer does not exceed those ratings.
For a drawbar Curt recommends the Curt Class II Drawbar - 2-5/8" Rise, 3-1/4" Drop - 7-1/4" Long - 3,500 lbs # C45521 which has a 2-3/4" rise. For a compatible 2" hitch ball you will need the # A-82, and for a hitch pin and clip you will... view full answer...
I reached out to my contact at Fulton and the 143200 you mentioned is only compatible with a cable.
If you are needing a cable you can use the Fulton Galvanized Winch Cable with Hook - 50' x 7/32" - 5,600 lbs # FWC7500100.
I included a video of the # FWC7500100 for you to take a look at. view full answer...
The Bearing Kit # BK2-100 is the correct kit for your Lippert 3500lb axle. This will include the inner and outer races and bearings with a new grease seal, cotter pin and tang washer.
I recommend using a Bearing Packer # PTW1218 with LubriMatic LMX Industrial Strength Grease # L11390 for the new bearings. This will ensure that you get grease throughout the bearing before installation. view full answer...
I am not 100% certain if you mean a hard plastic shroud that makes the top part of an air conditioner, OR if you mean a fabric storage cover to keep the "elements" out while in winter storage.
If you only need a storage vinyl cover then the ADCO # 290-3027 cover with draw string is a good fit.
For your Dometic B59516.711C0 Brisk II Air Conditioner, the shroud replacement is Dometic part number 3315332.000. We do not have this exact part. The closest replacement shroud is the MaxxAir... view full answer...
From Rep at PullRite, you will need to measure from the front edge of your king pin to the leading edge of the king pin plate to identify which you should use with your Rota-Flex 5th Wheel Pin Box and #LC328330.
See the attached image I provided with this, if that measures 5" then you need capture plate 331760. You can acquire this from PullRite. view full answer...
The BAK tonneau covers for your 2021 Nissan Titan XD, such as the BAK Industries BAK Revolver X2 # BAK39524, require the Utili-Track rails to be rotated 180 degrees before tonneau installation; the BAK covers do not allow for use of the Titan Box system which you have on your truck.
Since you have the OEM cargo box, I recommend going with TruXedo Sentry Hard Tonneau Cover - Roll Up # TX1588801. This is a roll-up hard cover, very similar to the BAK Revolver X2 that you were looking at. view full answer...
I may have an option for you, but the # DT45502 you were looking at is only confirmed to fit select 1980-1997 Ford F-100/150/250/350 trucks and will not fit your 1995 Ford F-450 cab and chassis.
Since there are no custom fit hitches confirmed to fit your F-450 the best option is to have a universal hitch like the Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver - Weld On - Class V - 2" # 41990-07 which fits frames that are 18" - 44" wide. This hitch will need to be welded to the... view full answer...
From the numbers you provided, your fully loaded trailer tongue weight should range between 500 and 800 lbs. I'll link to an article that describes a couple of ways to definitively determine this, but the easiest way is to use a tongue weight scale like the etrailer, part # e99044.
Given the likely range of your trailer's tongue weight, the Curt TruTrack, part # C17499 which is effective on trailers with 500-800 lbs of tongue weight would be ideal. The TruTrack provides proven weight... view full answer...
You could use the Curt 7-way to 4-way adapter part # C55384 to add in a 4-way basically behind your current 7-way and then use an extension like the part # HM48235 which is 12 feet long. You could use multiple extension if your camper is longer as needed. view full answer...
It sounds like you're looking for an RV cargo carrier for an 8" bumper that's 24x36" with a 500-lb capacity. I have a possible solution for you.
First, though, the only bumper-mounted cargo carrier we carry that closely matches the dimensions and capacity is the etrailer Cargo Carrier, part # e99050. It is 24x40" and has a 500-lb capacity. However, it only fits 4x4 or 4-1/2x4" bumpers.
A better option may be to install a hitch on your RV and use a hitch-mounted cargo carrier. For the... view full answer...
The RoadActive Suspension Custom Leaf Spring Enhancement Kit, part # RAS4611, is a great choice for your 2020 Chevrolet Silverado 1500 and is the one I recommend.
It turns your leaf springs into a mechanically active suspension system to give you a better ride quality with or without a load. It definitely helps with the sag problem. They're adjustable, putting them a step above SumoSprings, yet they adjust automatically, putting them above the air springs. They have a 2000-lb capacity... view full answer...
Go To Results