The Curt Front Mount Trailer Hitch item # C31082 weighs 28 lbs. It is confirmed to fit the 2017 Honda Ridgeline.
I have attached the installation instructions below so you can see how to get this hitch set up. view full answer...
I reached out to Erickson, who said the nuts on the Erickson Flag Pole Holder # EM85HR were 10 mm but they did not have the threading.
I have added a link below to a video review for you to check out as well of the Erickson Flag Pole Holder # EM85HR. view full answer...
Curt Front Mount Trailer Hitch Receiver # 33328 for your 2012 Honda Ridgeline weighs approximately 23 pounds. I have included a link to the installation details for you. view full answer...
I went out to the warehouse and pulled the Cipa Clip-on Towing Mirror, # 7070 and I produced a short video showing the dimensions of the Clips on the mirror that you asked about, see link.
The outside distance between the bottom clips on this towing mirror is 4 inches and the on center distance is 2-7/8 inches. The top clips that the strap attaches to are spaced 2-7/8 inches on center and 3-1/4 inches outside to outside. view full answer...
The A-Frame Trailer Coupler with Yoke Latch # CA-5210-B weighs just over 7-lbs. The black powder coat finish is great for resisting corrosion and it has an 8000-lb capacity. view full answer...
I went out to the warehouse and put together a Swagman Chinook 2 Bike Platform Rack - 1-1/4" and 2" Hitches - Frame Mount - Tilting Item # S64683 to measure it for you. With the center mast folded down it measures 14 inches from the top of the receiver opening to the highest part of the rack. With the mast folded down and the rack tilted up it is approximately 16 inches from the top of the receiver opening on the hitch.
Basically measure from the top of the receiver opening on your 2017... view full answer...
The only reason the holes of the Draw Tite part # 75280 wouldn't line up with the frame holes of your 2006 Honda Ridgeline would be if it was bent in shipping which is unfortunately something that happens periodically. The brackets can pretty easily bend back though and as long as the paint doesn't flex or the metal crease it's totally safe to use. view full answer...
This Roadmaster Trailer Hitch Extension # RM-071 would not be the correct hitch extension for you. You might be able to use an 8 Inch Hitch Extender for 2 inch hitches # e88YR. However, you should note that if you use a hitch extender you essentially cut the towing capacities of the hitch in half.
The # RM-071 that you referenced is designed for flat-towing purposes only.
I attached an FAQ article on hitch extenders for you to check out also. view full answer...
The Rhino-Rack 2 Kayak Carrier (the 2 kayak carrier is made using # S512 paired with Expansion Arm # RRS512X ) will mount to the factory crossbars on the 2019 Honda Ridgeline without any problems, but from what I was able to find from my research, it might not be able to carry the weight of your Hobie Mirage kayaks. Since this carrier has a 110-lb weight limit, and it appears that your kayaks weigh about 60-lbs each, the Rhino-Rack carrier may not be the best option for you. If you weigh... view full answer...
Weight distribution systems like the Equal-i-zer # EQ37100ET really do need to be matched to the trailer's actual fully-loaded tongue weight (TW). Using a 1000-lb system with a smaller travel trailer like your R-Pod can result in jumpy and unpredictable handling from the trailer and this is not recommended.
The good news is that it is easy to change the rated capacity of the system by changing out just the two spring bars; you do not need to replace the whole setup. You can replace the... view full answer...
The 2,500 lb capacity of the Stromberg Carlson Electric A-Frame Tongue Jack # JET-2500 is referring to the tongue weight, and is the lift capacity of the jack.
I've added links to a pair of video reviews on this jack for you to take a look at as well. view full answer...
In regards to the Thule Force XT XL Rooftop Cargo Box part # TH6358B, you will need to install this so that the roof box is centered between the crossbars. This will ensure you have the best weight distribution possible allowing you to reach the full protentional of the box. Furthermore, when loading the box you'll need to place 1/2 of the cargo in the center and the remaining 1/2 of the cargo split between the front and rear. In regards to overhang, we don't have exact measurements to... view full answer...
The MaxxTow Ball Mount w/ 2" Accessory Receiver # MT70066 has a Gross Towing Weight (GTW) of 5,000 lbs and a a Tongue Weight (TW) of 500 lbs. The 500 lb TW is a combination of both the top receiver and the ball mount.
Typically the TW of a vehicle is about 10% of the towing capacity. Since your 2018 Honda Ridgeline is rated for 5,000 lbs of towing it most likely has a TW of 500 lbs. You would be pushing or exceeding the TW of both this ball mount and your Ridgeline with your power wheelchair... view full answer...
The Extang Trifecta Signature 2.0 # EX94590 has aluminum frames under the tarp, so rarely is any of the weight that is placed on the tonneau ever going to be fully supported by the tarp itself. The tarp on the Trifecta comes permanently attached to the frame for this added support. It's also worth noting that the cover is sewn into the perimeter frame and corners instead of using the hook-and-loop strips found on other tonneaus, which will help with it's strength and ability to withstand... view full answer...
Yes, there are longer crossbars but not a 66" one. Rhino Rack has a 65" item # RRVA165B-2 and a 71" item # RRVA180B-2. Those are the two closest options to 66".
To attach these crossbars to the naked roof of your 2023 Honda Ridgeline you will need the following parts:
Rhino-Rack 2500 Series Legs for Vortex Aero Crossbars - Naked Roofs - Qty 4 item # RRRLKVA
Custom DK Fit Kit for 4 Rhino-Rack 2500 Series Roof Rack Legs - Naked Roof item # DK470 view full answer...
The Timbren Axle Less kit part # ASR1THDS01 provides a 2,200 lb rated axle. As a set it essentially is a 2,200 lb axle. From the three holes to the bracket that the frame rests on measures 1 inch. view full answer...
I have attached a dimensional photo of the Curt Single Hook Coiled Safety Cables with S-Hooks part # C80151 and the larger Curt Single Hook Coiled Safety Cables with S-Hooks part # C80176 for you as it would be a bit difficult to explain the dimensions via text. If you have any other questions please feel free to ask. One of these options should work with the safety chain loops on your 2019 Honda Ridgeline but if not you would want to use a clevis style type hook like the Long Safety Chain... view full answer...
No, it won't but I have one that does. The Hopkins item # HM47570 is just an adapter that plugs into a round 7-way connector. To connect to your Ridgeline's factory 7-pin you will need the T-Connector Vehicle Wiring Harness with 7-Way Trailer Connector item # 118288. This will replace your 4-way.
If you want to have both a 7-way and 4-way connector on your Ridgeline you'll want to install the Hopkins Endurance Multi-Tow Twist-Mount 7-Way RV and 4-Way Flat Trailer Connector item # HM40920... view full answer...
I reached out to my contact at TruXedo who said that the Replacement Rear Header Seal # TX1703256 is 1-1/4" wide. This is a fit for the TruXedo Original Tonneau Cover and is sold by the foot. If you let me know what tonneau cover you have on your 2008 Honda Ridgeline I can see if we have the correct replacement seal for you. view full answer...