There is a trailer hitch receiver fit for your 2021 Honda Passport, with the best option being from Draw-Tite because it has the best bumper clearance, and because it has the best chance to allow your hands-free liftgate to work. The correct part number for that hitch on a '21 Passport is the following:
- Draw-Tite Max-Frame Trailer Hitch Receiver # 76290
While it is possible that the hands-free liftgate can be lost, it does still work for most people by kicking your foot to the side... view full answer...
You will not need to use any other converter or adapter on your 1999 Honda Passport or trailer to power the trailers LED lights using the T-One Vehicle Wiring Harness with 4 Pole Trailer Connector, # 118360. The wiring harness and vehicle electrical system support LED trailer lights. I have included a link to the installation details for you to view. view full answer...
The Draw-Tite Max-Frame Trailer Hitch # 76290 that fits your 2019 Honda Passport can interfere with the hands-free liftgate feature. You will likely have to kick your foot to one side of the receiver as opposed to the middle or it could be lost.
This is a Class III hitch with a 2 inch receiver and a 6,000 lb towing capacity with a hefty 900 lb tongue weight capacity though you should always be sure to verify your Passport's towing capacity in your owner's manual.
I have added a link to... view full answer...
The etrailer hitch item # e44AR you referenced has the same protrusion from your rear fascia as the Curt Trailer Hitch Receiver item # C13421. These hitches are manufactured by the same company and are identical except for the matte coating on the etrailer hitch over the gloss coating on the Curt. The hitch pin hole on both of these hitches sits 4" inside of your Passports bumper. The end of the receiver is online with the rear bumper of your Passport. I have linked an installation video... view full answer...
The Yakima LockNLoad Platform Roof Tray part # Y05044 will fit to your factory cross bars with 2 sets of the Crossbar Clamps for Yakima LockNLoad Platform part # Y05039. This will be as low profile as possible with the factory cross bars, the clamps are 1" tall and the platform itself is about 4" tall. view full answer...
The 1997 Honda Passport and 2002 Honda Passport (with door-mounted spare) use different trailer hitches so they are not interchangeable. There is just one trailer hitch confirmed to fit the 2002 Passport with the spare tire on the rear hatch. It is Curt trailer hitch # C13235.
If you plan on doing some towing I recommend etrailer ball mount kit # 989900. It comes with 2 ball mounts; one with a 3/4 inch rise or 2 inch drop and one with a 2-3/4 inch rise or 4 inch drop. It also includes... view full answer...
The best hitch for your 2023 Honda Passport is going to be the Curt Trailer Hitch Receiver item # C13421. This hitch is custom fit and bolts to your Honda with included hardware.
I really like the Curt hitch because it installs right below your rear bumper cover and and the only portion visible is the 2" x 2" receiver. This is a class III hitch with a 2" receiver. It has a 5,000 lbs towing capacity, and a 750 lbs maximum tongue weight. So you will have plenty of ability to haul cargo in... view full answer...
Out of the two hitch receivers we have for the 2022 Honda Passport neither of them will go through the rear bumper. They will install and sit directly underneath the bumper, about an inch, but will not extend past the bumper. You will not need to trim or cut any holes.
I recommend the Draw-Tite Max-Frame Trailer Hitch Receiver - Custom Fit - Class III - 2" # 76290. It has a higher tongue weight capacity and max trailer weight capacity, 900 lbs and 6000 lbs respectively.
It comes with... view full answer...
The Curt Trailer Hitch Receiver # C13421 is confirmed to fit your 2023 Honda Passport and will allow you to use your bike rack.
This hitch is made in the USA, has a bolt-on, no-drill installation and will provide you with a 2" hitch receiver. The 2" receiver is the most common size used for hitch mounted accessories such as bike racks, cargo carriers and ball mounts. view full answer...
I would be happy to help you set your 2019 Honda Passport up with a functional 7-way connector. The Tekonsha T-One Vehicle Wiring Harness for Factory Tow Package item # 118291 you were referencing will not work with an existing 4-way connector or function as designed by splicing it in. This adapter plugs into your vehicle's factory tow package wiring harness. The converter plugs into the factory wiring harness in your rear cargo area, on the driver's side. This adapter only works if you... view full answer...
Yes it does! I verified with Curt for you that their trailer hitch receiver does fit a 2020 Honda Passport Sport, and AWD is not a requirement for fitment. The correct fit for your '20 Passport Sport is the following hitch:
- Curt Trailer Hitch Receiver # C13421
This is a very simple bolt-on installation and will allow you to tow your trailer. For the wiring harness, the correct fit for your 2020 Passport is from Tekonsha:
- T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer... view full answer...
I always refer to the owner's manual when it comes to safety issues with vehicles and according to my research the online manual for your 2020 Honda Passport says you shouldn't need one but if you want to use one then it needs to be setup properly. As long as the hitch you're installed on your Passport is rated for a weight distribution hitch (WDH) then you should be just fine to use one.
For your application I recommend using the Blue Ox TrackPro Weight Distribution w/ Sway Control #... view full answer...
Though the Curt # C13421 will definitely fit your 2021 Honda Passport, installing any hitch may interfere with Hands-free Liftgate sensors and functionality may be very limited or possibly lost. However, it is exceptionally rare for the use of the sensor to be completely lost. Typically you will just need to mess with it a little to find the spot where your foot will activate it and you will be good to go. If you check out the install video I included, the sensor is talked about as well. view full answer...
No, the 2023 Honda Passport TrailSport would require a 53" Thule Wingbar Evo # TH711420. If you don't already have the feet you'll also need the Evo Raised Rail Feet # TH710401. view full answer...
To install a Yakima roof rack on your 2021 Honda Passport you need at least 50" JetStream Crossbars # Y00425 and the TimberLine Towers # Y33TR or the Yakima TimberLine FX Roof Rack # Y78UV that has ore or a clamp style connection as opposed to the straps.
If you don't have either of these setups then I can't recommend using an alternative setup even if you're able to get it to fit.
A while back we had someone fit a roof rack to a vehicle and while it technically "fit" and stayed put,... view full answer...
The Yakima Roof Rack # Y00426 and # Y33TR is a great option. This rack features JetStream crossbars with an aero design that limits wind noise and also looks great on your 2019 Honda Passport. It has a very extensive history of reliable use and comes with a limited lifetime warranty.
Thule Hullavator Pro Kayak Carrier and Lift Assist with Tie-Downs # TH898 is compatible with aero bars and will work great for loading a kayak on your roof. This kayak carrier is very popular for not only... view full answer...
The Honda sensor kit you're talking about is a relocation kit so the hands-free liftgate will function as normal with a hitch installed. You can install either the Curt # C13421 or Draw-Tite # 76290 hitch on your 2022 Honda Passport and it shouldn't completely cover those sensors though. You should be able to just kick to either side of the receiver for the sensors to pick up your foot as opposed to swiping under the bumper like normal.
The adapter kit is separate from the OEM hitch (although... view full answer...
The Konig Self Tensioning Low Pro Snow Chains # TH04115265 are a low profile chain that is Class S compatible- meaning that they are designed for vehicles with limited clearance in the wheel wells. These chains require 10mm of clearance in the wheel well.
I've linked one of our review videos that shows these chains being used on a Jaguar SUV with extremely low clearance in the wheel wells to give you an idea of how low profile they actually are! view full answer...
I can certainly understand wanting to save as much money as possible, but the only two trailer hitches that fit your 2019 Honda Passport are:
- Draw-Tite Trailer Hitch Receiver # 76290
- Curt Trailer Hitch Receiver # C13421
The reasons are tied into exactly what you referenced in the difference between the Pilot and Passport. Each trailer hitch is manufactured to fit specific vehicles, and this takes into account exacting details such as space between bolt holes, frame widths and parts... view full answer...
For the best fit and safety the custom fit hitches by Curt # C13421 and Draw-Tite # 76290 are your best options for your 2021 Honda Passport. These hitches are custom fit so that you will not have to drill into your frame or modify any of your bodywork.
I recommend the Draw-Tite Max-Frame Trailer Hitch Receiver # 76290 as it has the tabs mounted to add the 7-way directly to the receiver.
The T-One Vehicle Wiring Harness # 118291 will plug into the connectors on your Passport and give... view full answer...
Go To Results