According to Maxtrax, the mounting holes on the # MA24ZV are 10" on center across the width of the board and 25" lengthwise. All of the mounting pins like # MA48PR use M10 bolts so you will need to drill an appropriate hole based on the type of mounting surface.
I attached a link to all of the mounting hardware below for your reference. view full answer...
With trailer tires you want to inflate them to the max psi figure when cold to ensure you get the full weight capacity and you don't create excessive heat build up due to sidewall flex. view full answer...
Thanks for the info and photos, Joe!
From what I'm seeing in your photos it looks like the Mini-Illuminated 12V Switch # 37212765 could be a great option for you.
The switch measures 1-1/4" tall x 3/4" wide x 3/8" deep and fits a cutout of 3/4" tall x 1/2" wide. If this matches what you have then you'll be good to go! Otherwise Let me know what the dimensions of are your switches you need to replace and let me know what you have so I can compare that with our selection. view full answer...
The Swagman E-Spec Bike Rack for 2 Electric Bikes # S94FR has a 70lb per bike capacity when mounted to an RV, like your travel trailer. You would need to reach out to the manufacturer of the trailer to determine the weight capacity of the bumper to ensure it can handle the weight of the bikes and rack. If it can then you can use the Curt RV Bumper Mounted Hitch # C19101.
If not, then you'll to install an adjustable mount trailer hitch receiver. To find the correct size you'll measure... view full answer...
I went to our warehouse and measured the Buyers Products 50 Ton Air Compensated Pintle Hook # 337PH50 to get the height dimensions. The overall height of the pintle when open is 12" and when closed is 9-1/2". I also took a measurement for the height from the center mounting hole which you can have as reference point if your recessed area already has the holes drilled. When open it is 9-1/4" to the top of the hitch and 6-1/2" when closed. I have included images below with these measurements... view full answer...
Hi Craig,
RV city water inlets are typically all the same size but the mounting style and flange size can vary so you'll want to measure the current flange to determine if the # 372160-85-A-26A's 3" flange diameter will be enough to cover the cutout hole. Recessed mounts typically require a bigger flange to cover the hole. If you can send me some measurements on your current inlet I'd be happy to verify.
To seal your new inlet you'll want to use a bit of butyl tape # AL28FJ on the mounting... view full answer...
The 68 inch length of the etrailer fenders part # HP88VR is the overall length of the fenders from end to end. This does not actually have bolt holes so I couldn't give you that info as well. view full answer...
RV water heater sizes have shrunk a bit over the last few years so you may have to do a bit of framing to install a new tankless water heater. Based on the dimensions of the GC10A-4E that I'm seeing you could possibly get away with just a 16" x 16" access door with the Furrion Tankless Water Heater # FR98SR. If you measure your current door and find you need to go larger with the 16" tall by 18" wide then you'll want part # FR48SR instead.
I've attached a video to help walk you through... view full answer...
The height (as if the hub was resting on a table top) is 4-1/16 inches for the Dexter Trailer Idler Hub Assembly for 2,500-lb Axles # DX22XR. view full answer...
36 lbs. The Trailer Axle with Idler Hubs item # e32GR weighs 36 lbs. It has a 5 on 4-1/2 bolt pattern and a 2,000 lbs capacity. It measures 72" from hub-face-to-hub-face and 58" from spring-center-to-spring-center. view full answer...
If you have 12" wide tracks you can use the JR Products Screen Door Slider - 12" - Black # 37211175 you were looking at. We don't have anything that is 11-1/2" tall so I recommend measuring the width of the tracks for the slide to be sure. view full answer...
The answer to your question depends on where the hitch sits on the Bronco and how far the tire sticks out. This is not information that we have so you will have to use our measurements to compare on your Bronco. The distance from the center of the hitch pin hole to the closest part of the Kuat Piston Pro # KU76ZR and Piston Pro X # KU98VR is 10-1/8". If this is enough to clear the spare then it will work.
More than likely you will need additional clearance. In this case, the best solution... view full answer...
Thanks for reaching out, Michael!
As long as you're within 1" of being level you'll be just fine.
I will say that in your case I'd recommend picking up a 0 drop ball mount like the Flint Hill Goods Tri-Ball Mount # FHG62VR so you're 1" above what you need rather than 1" below. Reason being that when you couple up to the trailer your vehicle ball mount will naturally squat just a little so if you're 1" above what you need, it will help level things out a little once everything is hooked up. view full answer...
Hey Marc, I contacted Buyers Products was able to get that measurement for you, and the distance is 2-3/4 inches from the center of the hitch pin to the gusset on the Buyers Products 2" Pintle Hook Mount # 337PM812.
For a compatible pintle hook and hardware use Pintle Hook # 337PH6 and # 3378520. view full answer...
There's unfortunately not a guide to tell us the sizing of your trailer's jack pads so you'll want to measure and note the shape of each pad. I've run into numerous situations where the front and rear pads were either different sizes or shapes to work with the space available.
The SnapPad # SN88FR you were looking at are designed to fit four 9" round pads and two 12" round pads. If you can let me know what your shape and dimensions are I'd be happy to pick out the correct package. view full answer...
Hey Echo, so if the part # SP502L matches all of the dimensions you can take I would say it's pretty safe to assume it would fit and work great. Worst case scenario the attachment on top of the ladder might need to be relocated or modified. view full answer...
To find which steps fit your Intech Sol Horizon Rover you will have to measure. The Lippert pull-out steps attach the underside of the camper chassis, directly beneath the doorway. To decide which size you'll need, locate the space available underneath your camper that lines up with the door frame, and measure the width and depth.
To determine how many steps you'll need, measure from the mounting point to the ground. This is called the entry height. The entry height should roughly match... view full answer...
Hey Jason, we just received one of these Replacement Brake Levers # T0776600 in stock and I was able to get the measurements you requested. I hope you don't mind if I use the picture you made.
A: 9 9/16"
B: 1"
C: Outside to outside:1 1/16"
Inside to Inside: 13/16"
D: Full length: 8 5/8"
To center of the pivot: 8 1/8" view full answer...
Hi Kathi,
Anode rods are sacrificial hunks of metal that are designed to deteriorate so that the metal of the tank won't. A bit more length for the rod would just mean that this new anode rod would last longer. Most RV water heaters require an anode rid with a 3/4" NPT thread size so you'll want to measure the opening to see if the 1/2" # CAM11593 would be a compatible fit. When you open the door there should be a few stickers with some information about the water heater and the model... view full answer...