Trailers do not have specific pin boxes assigned to them so the only way to know the correct Reese Goose Box you need for your Grand Design Reflection is to know the model of pin box that is on it (we have no way of knowing this information, which is why you'll need to find it).
Thankfully, this is simple information to find out; if you do not have the trailer in hand yet just contact your local dealer with the VIN and you can contact Grand Design and they will let you know. Or, if you... view full answer...
The tire I recommend you go with in the size and load range you mentioned is the Provider ST235/85R16 Radial Trailer Tire part # TTWPRG235R16 which has an 81 mph speed rating. This is an excellent heavy duty tire option that comes with a two year warranty. It has a max fill psi of 110 psi. In regards to what we recommend filling trailer tires to, it's always the max psi listed on the sidewall while cold. The reason for this is simple, that's what the tire manufacturer recommend so we must... view full answer...
No, the etrailer # e28SR would not work for your 2017 Grand Design Reflection with 5,200lb axles.
To find the correct spring you need to jack up one side of the trailer so there is no weight on the spring at all, as weight will make the spring get longer, and then measure from center of eye to center of eye.
If the 26" measurement is with weight on the spring, then there's a good chance you'll instead need the # e76SR instead which has a 5,300lb rating and measures 24-7/8" long.
Let... view full answer...
The hose and fittings sizes are standardized for RV's. Therefore, what you have is going to be a type 1 to either a 1/4" NPT or 1/4" Male Inverter Flare. If you have the former I recommend part # 100473-12 or part # 37207-30715 if you have the latter. That said, I get why you're confused as these fittings don't actually mic out to 1/4", they will measure larger but that does not correlate to their nominal size which would be the same for measuring any sort of NPT fitting. view full answer...
Personally I prefer the SnapPad XTRA Jack Pads # SP54FR4 over the Stromberg Carlson # SC99MR as they have been around much longer and proven themselves to be a quality product. Both these will fit 4 jacks with a 9" round landing pad. view full answer...
The best thing you can do for your suspension on your 2017 Grand Design Reflection 337RLS is to add some jounce springs. The Overslung SumoSprings # SS26MV provide additional stability to your leaf springs. They will also help to reduce the amount your suspension compresses on the kitchen slide side due to the additional weight on that side of the trailer. You will need 2 of these kits for your tandem axles.
If you were to install 7,000LB Springs # e64SR your suspension will be stiffer... view full answer...
If you wanted to use the # K71-358-00 on a tandem axle trailer you would need to order two of these kits. Each kit provides enough components for a single axle so with two of them you'd have a tandem axle covered. view full answer...
I have attached for you below all the parts you requested for your 2019 Grand Design Reflections 303RLS.
5-Leaf Double-Eye Spring part # e34SR
MORryde Suspension Upgrade Kit for Tandem Axle Trailers part # MR46ZR
MORryde Shock Absorbing Suspension Equalizers part # MR27ZR
MORryde U-Bolts for 5,200-lb to 7,000-lb Round Trailer Axles part # MR66ZR
I know you said you wanted to use the Dexter EZ Flex but the MORryde CRE300 are much better as they offer more travel which equals better shock... view full answer...
Your trailer height might be increased a little bit but the difference in dimensions for your Equa-Flex Cushioned Equalizers # LC279687 to the Road Armor Shock Absorbing Equalizer Kit # LC696740 isn't significant enough for it to really make a huge difference so you'll be just fine swapping those parts out with each other! view full answer...
When applying the Alpha Systems Patch Kit for SuperFlex RV Roof Membranes - Almond - 3' x 2'
Item # AL84CV to the roof of your 2019 Grand Design Reflection Fifth Wheel, you will need to hold the patch material in one hand while heating the area that is to be repaired. As the material is being heated, apply the patch material in a reverse peel motion.
Here is the repair procedure from Lippert:
1. Identify the size of the area and thoroughly clean with mild soap and water.
2. Cut an oval... view full answer...
Using the Garden Hose Adapter part # LC360788 to balance the gray tanks is a matter of using it to add water to the tanks so that they all have an even amount. view full answer...
The sticker on the Dexstar Steel Mini Mod Trailer Wheel # AM20742 has it rated for 3,520 lbs so it will work great for your application! view full answer...
Yes, the TorkLift GlowStep Revolution Scissor Steps w/ Landing Gear # TLA8004 is what you'll want for a 2019/2020 Grand Design Reflection 337 5th wheel camper. I confirmed this with TorkLift and also attached a review video for you to check out. view full answer...
The best suspension upgrade for a Grand Design Reflection is the MORryde Premium Rubber Suspension Kit, part # MR97ZR for 33" wheelbase or part # MR47ZR for 35" wheelbase. This is a kit that comes with cushioned equalizers for shock absorption, wet bolts for easy maintenance, and a crossmember for increased rigidity. It also provides a 2" lift over the factory suspension and comes with an extended warranty. view full answer...
The 6,000-Watt Portable RV Inverter Generators - 5,500 Running Watts - Parallel Kit # 333-0003-2-0007 comes with the two generators needed as well as the parallel kit with a 50 amp outlet like you are looking for so it would be what you'd need. view full answer...
Yes, a hitch-mounted motorcycle carrier would be your best option for carrying your Vespa 150 scooter on your 5th wheel travel trailer. I think the best carrier for you is the Ultra-Fab Dirt Bike Carrier # UF48-979033. This is RV-compatible and has a built-in ramp to allow for easy loading or unloading. Front and rear wheel holders are adjustable to accommodate various sizes of motorcycle or scooter tires.
You will need tie-down straps to secure your scooter; I would go with Erickson Motorcycle... view full answer...
If you are wanting to retract the front landing gear jacks all the way you should support the front of your 2021 Grand Design Reflection by either reconnecting to your truck or using some sort of stands for the camper to sit on.
You will only have to manually raise the jack cylinder that has reached its stroke limit with the control pad and then clear the code.
To clear an error code from the touch pad, repair or otherwise correct the issue, then press “ENTER.” If the error is still... view full answer...
Without seeing the other side of your regulator it's hard to know exactly what the connection is but it should be a 1"-20 fitting so you would be good with using the MB Sturgis Quick Disconnect Propane Hose for Small Appliance - Disposable Cylinder Port - 10' Item # 100476-120-MBS.
Whenever you purchase your new grill just shoot us a pic of the connection and we can verify the correct fitting needed. view full answer...
Since your Lippert Electric Tread Lite Step for RVs # LC353543 is made of aluminum, the Lippert Solid Stance RV Step Support # LC96BJ will not work for you, unfortunately.
instead, you'd need steps made of steel like the Lippert Manual Pull-Out Step for RVs # LC432687.
You will also need at least 5" of ground clearance to ensure you have a proper fit. I have attached a couple videos for you to check out as well. view full answer...
The 35 ft. lbs of torque you have now would not be enough for your wheel, it is quite a bit less than recommended. The hub on the Kodiak Disc Brake Kit # K2HR526D has 1/2" wheel bots and for that size bolt on a 15 inch wheel the recommended torque is 90 - 100 ft. lbs for an aluminum wheel (and 90 - 120 ft. lbs for a steel wheel). That said, wheel stud threads need to be visible outside the wheel nut and though there can be varying amounts of thread sticking out, as a general rule there... view full answer...