We may have some potential options for replacing the tack room door lock on your Featherlight trailer. Is the 5" L x 5" H dimension you gave for the door cutout or the lock itself? The best way to find the right replacement lock is to go by the cutout size.
If your cutout is 5" x 5" we do not have a lock that will fit those exact dimensions. The closest thing we have is the Bauer Products Motorhome Door Lock # BA64FR which will fit a 5-1/4" wide x 4-1/2" tall cutout. Is it made for a... view full answer...
While we more than likely have a hitch or hitch plate that will fit your 2003 Freightliner Columbia, we do not have one that is confirmed to fit.
With that being said we still may have an option that will work for you, you will just need to measure the width of your frame.
If your frame is 34" wide then an option like the Buyers Products Hitch Plate with Receiver Tube # 3371809065 you were looking at would work. This hitch will need to welded and bolt to the frame.
If your frame is not... view full answer...
The best way to make your Freightliner compatible with a trailer 7-Way is to test the functions with a circuit tester # PTW2993 and match sure they match. I'm attaching pin-out diagrams of both the trailer and vehicle 7-Ways that you can use as a guide to make your connections - just be sure to wire everything up by function and not by the wire color. You will be able to gain access to the wiring connections through the back of either 7-Way, either by moving the sleeve out of the way or... view full answer...
For your 2005 Monaco Diplomat 40PDQ Pusher RV I recommend product # RM-1209-119 which is a confirmed fit for your 2005 Freightliner Sterling chassis. This product will minimize side-to-side movement which will improve overall stability allowing you to execute turns and quick maneuvers with confidence and minimizes the effects of crosswinds. There are currently no supported steering stabilizers or rear anti-sway bars for your chassis. view full answer...
The distance between the bolt holes on the Curt Trailer Hitch Receiver # 14080 is 39-1/4" center-to-center. I have attached a photo to demonstrate this. Please note that this trailer hitch fits the following:
2002 - 2002 Chevrolet Avalanche
2002 - 2002 Cadillac Escalade
2002 - 2002 Cadillac Escalade EXT
2001 - 2002 Chevrolet Suburban
2001 - 2002 Chevrolet Tahoe
2001 - 2002 GMC Yukon
2000 - 2002 GMC Yukon XL
2000 - 2000 Chevrolet Tahoe excluding Limited and Z71
2000 - 2000 Chevrolet Suburban... view full answer...
For a vehicle like yours that has separate turn signals from stoplights you'd need a trailer wiring setup that has a converter box like the part # 119250KIT which was designed for this type of application. view full answer...
I highly recommend using the Tekonsha Prodigy P3 # 90195 for your 2019 Freightliner XC-Series chassis because the P3 has a nice LCD screen that makes it easy to read and make adjustments, plus you have the ability to save various settings depending on what you might be towing behind you. I'm not aware of any plug-n-play connectors on your chassis but you should be able to splice in the included pigtail to the existing wiring on your motorhome. Simply match the following wire colors of the... view full answer...
I went to the warehouse and pulled one of the support pegs, part # 8535. I took some measurements of the bracket used to mount the support pegs and they are shown in the attached photo.
The bracket outside dimensions are 2-1/4 inches x 1-1/4 inch. The distance from the mounting holes center-to-center are 13/16 inches and 1-3/4 inches. view full answer...
The Roadmaster Dual Hitch Receiver Adapter, 8" Drop/Rise # RM-077-8 was designed for exactly this purpose. The 8" rise will allow you to mount a bike rack up higher than your vehicle, providing plenty of clearance between a bike rack and the flat towed vehicle. view full answer...
Hey Scott, so our records show that sometime in 2003, Freightliner made design changes to their suspension which affected fitment of pretty much all of the Roadmaster sway bars and steering stabilizers. In our conversations with Roadmaster, the only potential option for a 2004 Freightliner is the # RM-RBK14-RSSA. There are a few requirements for fitment though. The RV must have air suspension, it must have a solid front axle, and it must not be equipped with a 150-gallon fuel tank. If your... view full answer...
Yes, we have a replacement motor that will work for your 2006 National Tradewinds. I contacted the manufacturer to verify that the Replacement PowerGear RV Above Floor Slide-Out Motor # LC368417 is the correct motor to replace the 130-1204G you currently have. view full answer...
There are no specific fits for a 2013 Freightliner M2 for a hitch or wiring, so your best option is a weld-on hitch. If your frame is up to 44 inches you can use the Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver # 41990-16 for 16 inch tall brackets or Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver # 41990-07 for 7 inch tall brackets.
Then for a 7-way you will need to hardwire in the Vehicle Wiring Harness # C59236 with the Universal Installation Kit for Trailer... view full answer...
The lug nut cover part # WMRMT9061 is made from stainless steel and could work if you have a 20 mm lug nut on your wheels like the part # WMRMT9063 that this was designed to fit. We do not have anything made from tin though. view full answer...
The small amount of wind that's on the very top of an RV like your Sprinter van might surprise you due to how it deflects and goes over most of the top of it instead of hitting it straight on. So what that means is that there wouldn't be much wind at all on the Furrion Chill part # F15PA12SASA-W and you'd be totally fine to do 75 mph. We've sold quite a few AC units over the years and not once have we had an issue with wind hurting one. view full answer...
I checked with Roadmaster and confirmed the Roadmaster Rear Anti-Sway Bar part # RM-1209-140 as a fit for a 2022 Tiffin Allegro Red 340 on Freightliner XC-Series Chassis. It doesn't look like we have any install videos at this time (they will be displayed on the product page when available) but after looking over the instructions which are attached below, the process looks pretty easy and straightforward. There is no drilling required, just nuts and bolts and you don't have to remove anything.... view full answer...
Glad to hear that you've enjoyed your past experience with the SumoSprings on your last motorhome. The Timbrens are constantly compared to/against the SumoSprings so since you liked the SumoSprings you'll enjoy the ride quality here as well.
The Timbren Suspension System # TFRM2L is for if you have a leaf spring suspension, but from what I could tell in my research I believe your 2019 Renegade Verona LX has an air spring suspension so you'll want the Timbren part # TFRM2A instead. Aside... view full answer...
Yes, the Buyers Products Sight Rods Horizontal Adapter Kit part # 3371308125 is required to install the Buyers Products 36" Fluorescent Orange Oversized Bumper Sight Guide part # 3371308160. view full answer...
While there is a way for you to carry a 70 lb electric bike on the back of a motorhome, there are no ladder-mounted bike racks that have the capacity to carry a 70 lb bike.
Instead you will need to add a trailer hitch, the Multi-Fit Motorhome Trailer Hitch # 5350, which you can do so long as your motorhome has a chassis from 24" to 46" wide, or the Multi-Fit Motor Home Trailer Hitch # 82201 for frame widths from 47" to 71" wide.
Once you have the right hitch you will simply need a bike... view full answer...
I spoke to my contact at Surco and she informed me that from the very top to the very bottom the Surco Ladder part # SP501L measures 97 inches.
The distance from the portion that attaches to the roof of the RV to the ladder is 17 inches. view full answer...