The arm of the Sidewinder part # RP34FR weighs approximately 145lbs and the turret weighs approximately 60lbs.
This will all come assembled as one piece though. view full answer...
For your 2019 Ram 2500 the correct Firestone Ride-Rite Red Label air bag kit is part # F2706. The air bags in the kit have a maximum diameter of 7.52 inches at the widest point, compressed height of 3 inches, and extended height of 8.91 inches. However if your truck is lifted a spacer may be required to make up for the additional height. I have attached a photo of where to measure, and once you find that distance you can choose from the following if a spacer is needed.
6-1/2" - 7-1/2"... view full answer...
Towing capacities sometimes can be hard to figure out and it can seem like there is conflicting info but on your 2020 Ram 2500 the towing capacity is spelled out pretty easily as it can tow up to 25,000 lbs of trailer weight with a pin weight capacity of 3,750 lbs. Pay load capacity is a different number as it's basically the weight capacity of the truck bed whereas a trailer attaches to a hitch which attaches directly to the truck frame. The weight of the trailer you mentioned would easily... view full answer...
The SportRack Vista XL Cargo Box - Roof Mount - 18 cu ft - Black # SR7018 measures 38 inches at its widest point, measures 36 inches on inside width, and the mounting holes are 28-1/2 inches on center side to side according to my tech contact at the manufacturer.
It fits crossbar spreads front to back of: 23-5/8", 25-7/8", 27-7/8", and 29-7/8" measuring center on center from the front crossbar to the rear crossbar. view full answer...
In regards to the Rapid Hitch Adjustable, Locking, Aluminum Ball Mount Kit part # AM3400, the distance from the center of the hitch pin hole (closest to end of shank) to the backside of the vertical upright is 4-3/8" which is actually shown in the attached video. view full answer...
We cannot recommend you exceed the 200 lb tongue weight of the hitch that fits your 2019 Mazda CX-3, the Draw-Tite Trailer Hitch Receiver # 24933.
It is not designed to have that much weight so there's no telling if the structure can be impacted. This is the only available capacity for your CX-3, so if you want to haul your dirt bike with this vehicle the best option really is a trailer.
To do that you will need the hitch, along with T-One Vehicle Wiring Harness # 118718, Draw-Tite Drawbar... view full answer...
The Bulldog # BDW15001 winch installs using two mounting holes that are 3-3/16 inches apart on center. The full listing of specs is listed in our linked product description, and I've also provided a screen capture from Bulldog's website.
I've also linked to a product description video featuring the # BDW15001 ATV winch. view full answer...
The Curt # 16055 gooseneck plate measures right at 23 inches long by 12 inches wide. The tabs that mount into the bed rails measure right at 22 x 10 inches front to back and side to side respectively, measured center to center. The plate is compatible with industry standard 5th wheel bed rails, as long as the inner-most slots are about 10 inches apart on center. The trailer ball will extend to right at 5 inches above the mounting rails.
I've linked to a demonstration video for the # 16055... view full answer...
I've pulled the Curt Trailer Hitch Receiver # C13136 to take these measurements for you. The distance between the edges of the mounting bracket is 17-1/8 inches. From the top of the bracket to the top of the tube is 10-1/4 inches and from the top of the bracket to the bottom of the bracket is 12-5/8 inches. I've included a diagram to help show you! view full answer...
I recommend the LED Mini Trailer Clearance and Side Marker Light - Submersible - 3 Diodes - Amber Lens Item # 47-99-006 as your mini lights and the Peterson Thin Line Clearance or Side Marker Trailer Light - Incandescent - Oval - Amber Lens Item # 427400 for your 3" lights. These are actually 3-1/2" lights because we do not offer a 3". view full answer...
In regards to the Replacement Base Legs for Husky Silver Series 5th Wheel Trailer Hitch part # HT31325, the spacing between each mounting hole is 2-5/8" (center on center), the distance from the center of the mounting holes to the base of the leg (excluding tabs) is 7-1/4" , and the overall height excluding tabs is 8-1/2". view full answer...
The Draw-Tite # 24983 has a maximum tongue weight of 200-lbs, but your 2020 Toyota Corolla may have a slightly lower tongue weight and when towing/carrying items on the hitch you're always limited to the lowest rated component in the setup. As long as your vehicle can hold 200-lbs tongue weight then you can use the full capacity, but if the Corolla has less then you will want to abide by that number. view full answer...
I had our warehouse measure the Fulton XLT Bolt-Thru Swivel Trailer Jack # F141132 that you were looking at and with the jack fully extended and the handle pointed straight up it measures 47-1/2" tall.
From the center of the mounting hole to the top of the handle pointed straight up it measures 20-1/2", which you can use to determine if this jack will fit your application by measuring from the center of the jack mounting plate on your trailer to your boat. As long as this distance is greater... view full answer...
The amount of torque needed for the hitch ball you have installed on your Blue Ox weight distribution will be based on the hitch ball you have. Some require a great deal of torque like the Curt hitch balls like the # C40034 that require 450 ft lbs whereas some require less than that. We don't normally recommend impact wrenches but we do normally recommend longer torque wrenches. Since those can be expensive the best option might be to see if an auto parts store can loan you one. view full answer...
We've had this question before on the Draw Tite hitch # 76182 and we've found that the distance from the center of the hitch pin hole to the end of the hitch tube is 2-9/16 inches. view full answer...
The factory 08L92-TG7-1A0 hitch for your 2019 Honda Pilot has a 3500 lb towing/350 lb tongue weight capacity.
The Küat # NV22G combined with the # NA22G add-on weighs 82 lbs. When the maximum 200 lbs of bikes are added, the total weight would be 282 lbs, which is far enough under the 350 lb tongue weight of the Honda OEM hitch that you wouldn't need to worry about it. The hitch will handle that just fine.
If you use the provided links, you can see demonstrations for the Küat NV 2.0 and... view full answer...
In order to add a 5-way harness to your X5 you'll need to use the Curt Trailer Connector Adapter item # C57187 with a 4-way connector like the Curt Powered Tail Light Converter item # C59236 you were looking at. I am sorry but they don't make vehicle specific 5-way wiring harnesses which is why you need the adapter.
If your vehicle has a 7-way connector you will want to use the Wesbar Adapter item # 707250. view full answer...
No, its not but I have a better option. Instead of the Anti-Rattle Hitch Pin for 2" Trailer Hitches item # SHP2061, I recommend the etrailer Anti-Rattle Hitch Stabilizer for 2" Hitches item # e99007. This can be used with any 2" ball mount or accessory so long as your hitch has a collar around it for a stabilizer to work. If you're using this on an 2019 F-150 you're good.
It will help greatly with vertical movement caused by bouncing when you hit a pot hole because it tightens the connection... view full answer...
Bearings play no role in the maximum speed of trailer tires. The speed is based on the rating given to the tire from the manufacturer. If you don't have speed listed like on the # AM30020 then you can assume it is rated for the standard speed of 65 mph. If it is higher than 65 a trailer tire will have a rating with a letter like M which would be 81 mph. view full answer...