Expert Answers about Ford F-450 Super Duty

• Length Of The Bearing Buddy # BB2717SS That Sticks Out Past The Hub
• Hi Chris, The length of the Bearing Buddy Bearing Protectors # BB2717SS is approximately 1.935" from the lip that rests against the hub to the end with the rubber cover in place.
  view full answer...


• Question About a Product
• You can email me back with your pictures and I'll see.
  view full answer...


• Will these fit a 2019 Ford F450 Super Duty?
• Josh, the answer for these replacement rails is no. What model of tonneau cover do you have on your 2019 Ford 450 Super Duty? If you have model # 311-BLFA19A45 the Pace Edwards Bedlocker Retractable Hard Tonneau Cover - Electric - Aluminum - Black which is the only Pace Edwards branded cover that we have for the 2019 Ford 450 Super Duty 8 ft bed then the replacement rails would be part # 311-BL5145. If you do not have this model please let me know what you do have and I will take a look for you.
  view full answer...


• Will Gen-Y 5th Pin Boxes Void The Lippert Frame Warranty
• Hi James, To my knowledge the Reese Goosebox is the only replacement option that won't void the frame warranty. That being said, the frame warranty is typically only a year so you really aren't losing much voiding it, especially if you've had the trailer for over a year. To find the correct fit for your trailer you'll need to first determine the bolt pattern for your trailer and then measure for the fully loaded pin weight of the trailer. For example, the Gen-Y Hitch Shock Absorbing...
  view full answer...


• Using TPMS Flow Through Sensors And Valve Extenders On A 2024 Ford F-450
• Hi John, TST Flow Through Sensors # TST-507-FT-S2 are approximately 2-1/8" long so they do add a bit to the overall length of the coming from the valve. TST likely told you that the sensor has to be directly after the valve to avoid any movement with the sensor that could damage it or the valve and to help prevent any false readings. With valve extenders like the Wheel Masters # WM8001-135 you'll be able to tuck the excess cable up since you'd be mounting the end of the extender to the...
  view full answer...


• Can 18K Reese Signature Hitch be Replaced With 24K Reese Signature Hitch on 2008 Ford F-450
• Reese does not produce the Signature Series line of hitches anymore. They have been replaced with the Elite Series line of hitches. The new Reese hitch is the Reese M5 Series 25K Hitch, part # RP30922. It is rated for a gross towing weight capacity of 27,000 lbs. It also shows to use the Reese Fifth Wheel Installation Kit, part # RP30073, on your 2008 Ford F-450 Super Duty. I spoke with my contact at Reese and he said the # RP30073 kit is rated for what ever the towing capacity of the...
  view full answer...


• Recommended Highest Capacity 5th Wheel Hitch for the Ford Factory Puck System
• Hey Jason it does sound like your 2014 F-450 has the puck system in the bed. Since this is your first 5th wheel hitch and you're wanting some high end capacity, I recommend the Reese M5 5th item # RP68FR. This 5th wheel hitch has a massive 32,000 lbs capacity and will mount directly to the puck system for easy installation and removal. I really like the Reese M5 item # RP68FR because of its coupling process. It has a easy-to-see lock indicator for maximum safety and security. The one piece...
  view full answer...


• Does the Empire Faucets RV Kitchen Faucet # EM22WR Have a Removable Aerator?
• The Empire Faucets RV Kitchen Faucet # EM22WR does not have a removable aerator. This is going to be true for most all faucets this style and an easy solution is using a couple AquaFresh Interior Inline Replacement Water Filter w/ 1/2" Fittings # AF24FR. This is going to be similar to whole RV Filters # CAM40045 but has the much smaller fitting used on faucets inside an RV.
  view full answer...


• SumoSpring Kit that Fits 2018 Ford E-450 Motorhome Chassis
• Hey Scott, so we do have the SumoSpring Solo kit part # SSR-130-54 that is a confirmed fit for your 2018 Ford motorhome built on an E-450 chassis.
  view full answer...


• Troubleshooting A Ford (Reese) Factory 5th Wheel Hitch That Doesn't Want To Lock Properly
• Hi Craig, What you're experiencing is a pretty common issue for a lot of hitches and it tends to be either a lubrication issue or just an issue with the angle that the truck and trailer are sitting at preventing the jaws from fully latching. Newer 5th wheel hitches have a bit of pivot in the head to help accommodate this but it's not always enough so getting the truck and trailer on level ground will help quite a bit. With the hitch locking after you start pulling forward it sounds like...
  view full answer...


• Will Furrion 30A Female to 50A 125/250V Male Plug Into 30 Amp Inlet For 50 Amp Cord
• Hey James, Yes, the Furrion Marine Power Cord Adapter - 30A Female to 50A 125/250V Male # FP3055SY will do just that. It'll plug into your 30 amp inlet and allow you to add a 50 amp extension cord.
  view full answer...


• Can you Increase the Towing Capacity on a 2015 Jayco Precept 29UM on Ford F-53 Chassis?
• So your 2015 Jayco Precept 29UM is on a Ford F-53 18K chassis which is the limiting factor with a towing capacity of 5,000lbs. I believe this is the restriction you are having. The Curt Receiver # C14048 you found while having a higher rating will not increase your towing capacity. If you can find a lighter trailer or vehicle to tow you can install a Curt TriFlex NEXT Trailer Brake Controller # C24VV with the Wiring Adapter # C51322 which will connect under your dash. Check out the...
  view full answer...


• Replacement Clearance LED Lights For A 2018 Thor Chateau 28Z Class C Motorhome
• Hey Ed, Typically the light cover will have some small indentation for you to stick a pry tool in and pop off the cover. You can see if there's an actual bulb in there or more likely just led diodes. If it's a bulb you can look at the base for a bulb type and find a replacement. If it's just diodes then you'll be replacing the entire light. If you are needing to replace the light then you should be able to see the two mounting screws holding the base of the light to RV and can remove...
  view full answer...


• Can the Bluetooth control Kit Be Mounted Between the Cannister & a Tool Box
• Yes Jerry, the Bluetooth Control Kit for Pace Edwards Electric Tonneau Covers # PE63QJ should work fine between the canister and a tool box but you can fire it up and test it prior to mounting it. If you find that the signal isn't as strong, or that it's not responding you can just move it to a place with better signal.
  view full answer...


• Rear Sway Bar and SumoSpring Kit for 2011 Itasca Cambria to Improve Handling
• Hey David, actually what is going to make the biggest improvement in handling and stability for your 2011 Itasca is an upgraded rear sway bar with the part # RM-1139-175. I know that's not what you asked about but for motorhomes where most of the weight is out back the rear sway bars make a huge improvement. You won't see much of a difference going to a different steering stabilizer. This is also true for SumoSprings. A rear set like the part # SSR-118-54 with the rear bar will make a...
  view full answer...


• Tow Bar Lighting Solution for 1990 Jeep Wrangler
• Hey David, for your 1990 Jeep Wrangler the Roadmaster Diode Kit part # RM-15267 would be a really great option. This installs diodes on the Wrangler's taillight circuits which allows the RV to control them. It also comes with the wiring that runs to the trailer wiring at the rear of your RV. You did mention that you have a 6-pin but most likely what you have is the standard 7-way which also has a center pin that gets counted. You also mentioned 90 and 1991 so I am not totally sure what...
  view full answer...


• How To Determine The Correct PSI Levels For Firestone Air Springs On A 2023 Ford F-450
• Hey Donald, Air springs are designed to help eliminate sag so one of the easiest ways to see how much pressure you need is to measure from the ground up to the of the wheel well arch without the trailer to get your factory ride height. Then you can hook up to the trailer and increase the psi until you get the ride height back to factory settings, keeping in mind that the air springs do have a psi limit. If you wanted to run your air springs with a bit more air in them unloaded that's...
  view full answer...