Yes, there are a couple of ways to make a Curt A20 work in the Ford factory puck system. The easiest way is to use the Curt A20 5th Wheel Trailer Hitch item # C16034. This 5th wheel hitch comes with the legs that mount inside the Ford puck system.
If you already have the Curt A20 item # C16140 you were looking at, you can add the Curt OEM 5th-Wheel Hitch Legs item # C16017 or just use the Adapter Rails item # C88KR. Both options will work and not reduce the capacity. view full answer...
The 2 gallon tank that comes with the Air Lift QuickShot Compressor System for Air Springs # AL25690 has a 6" diameter and is 17" long. The brackets that you use to mount it add about 2-1/2" of height so we are looking for a space that can handle 8-1/2" High x 6" Wide x 17" Long for the tank assembly. view full answer...
The interior dimensions of the 23" x 51" UWS Cargo Carrier for 2" Hitches # UWS65XR is 20-1/2" x 48 1-/2".
As far as a floor, there is not a traditional floor but there are strips of aluminum that line the bottom vertically that act as a "floor". view full answer...
The fully retracted distance between the hooks of the CargoBuckle Mini G3 Retractable Ratchet Straps # IMF111640 that you referenced is 17-1/2 inches. I confirmed this with CargoBuckle.
I also attached a review video for these straps for you to check out as well. view full answer...
For as large a trailer as you have, a 42-foot 20,000-lb-GVWR Landmark 5th wheel, I absolutely recommend using a 24K-rated 5th wheel hitch to give you some safety margin.
Your 2017 F-350 dually is an excellent truck to tow this trailer, especially since it is a long bed that will naturally give you good turning clearance. And since you have the factory rail kit option you can use any of the three hitches shown on the linked page. All fit the factory pucks.
Curt's Q24 hitch # C16545-16017... view full answer...
The total weight of the:
-B&W Companion OEM 5th Wheel Trailer Hitch w Slider for Ford Towing Prep Package # BWRVK3370 for your 2022 Ford F-350, is 261-lbs.
I have included an installation video for you to check out as well. view full answer...
I would be happy to! The correct air bag kit for your 2003 Ford F-350 with a B&W gooseneck hitch is the Air Lift LoadLifter 5000 Air Helper Springs item # AL57291. These are custom fit and specifically designed to work with the B&W Turnoverball Gooseneck Hitches item # BWGNRK1108 or item # BWGNRK1108-5W.
For an air compressor, I recommend adding the Air Lift WirelessONE Compressor System item # AL25980EZ. This onboard compressor will allow you to adjust the PSI in your air bags from your... view full answer...
The canister on the Pace Edwards Full-Metal JackRabbit Hard Tonneau Cover # 311-FEFA19A45 sits just under the rails of the tonneau cover, so it will not be deep in your 2018 Ford F-350's truck bed. The canister measures 9.75" wide x 9.25" in diameter, though I'm not quite sure what you mean by its length from inside the truck bed to cover; if you can give me a bit more specifics in that regard I'd be happy to try and find out for you. view full answer...
The RetraxPRO MX Hard Tonneau Cover - Retractable - Aluminum - Matte # RT80383 will have a measurement of 11-5/8 deep by 13-3/4 inches long by 63 inches wide. I reached out to the manufacturer to confirm these dimensions and created a photo to assist.
This type of a cover will work extremely well with a tool box that opens from the front like the DeeZee Specialty Series Underbody Toolbox - Steel - 9 Cu Ft - Black # DZDB-2602 or the DeeZee Specialty Series Underbody Toolbox - Brite-Tread... view full answer...
The height adjustments for the Curt Q20 5th Wheel Trailer Hitch with Slider for Ford Towing Prep Package # C16530-16020 measure from 17-1/2 inches - 21-1/2 inches from the bottom of the truck bed to the top of the hitch skid plate.
I spoke with my contact at Curt and he confirmed that this is the height measurement for all of the Curt Q Series hitches when they are on a slider for the Ford Towing Prep Package. The slider causes the hitch to sit a couple inches higher than the Q Series... view full answer...
There is no absolute rule for spacing between the forward side of a 5th wheel hitch and a tool box mounted between it and the cab, but I would say 6 inches would be an appropriate minimum in most instances. We do have recommended clearance distances between the various points of the trailer and truck that you can see in the linked diagram. You want to ensure the front loft of the trailer can clear the top of the tool box. view full answer...
I spoke to my contact at Curt an he said a 1/2 inch diameter clevis hook would be perfect for use with the Curt Safety Chain Loops # C60691, so a 3/8" diameter clevis hook will fit just fine.
If you don't already have them, I recommend the Curt Clevis Hook with Spring Loaded Safety Latch # C81980. It's 1/2"diameter, features an 1-1/4" opening and has a capacity of 48,000 lbs. view full answer...
The B and W Companion Slider for Ford fifth wheel rail kits part # BWRVK3370 sits 8-11/32 inches forward of the front puck it installs into. So if you measure 8-11/32 inches in front of the forward puck you'd be able to tell if you have clearance for it to fit with your tool box. view full answer...
I reached out to the manufacturer and was told that if you have a Lippert 1116 on your 2020 Keystone Fuzion then yes, you can use the Reese Goose Box 5th-Wheel-to-Gooseneck Air Ride Coupler Adapter # RP85FR. It will fit so long as you use the Spacer Kit for # RP61301 you referenced.
I've added a link to a video review of the Goose Box for you to take a look at as well. view full answer...
The spacing for both the above-bed gooseneck and the M5 legs are 30 inches side-to-side and 13 inches front-to-back on center, as shown in the photo. So you can use the M5 legs, which are the following part numbers:
- Replacement Legs for Reese M5 5th Wheel Trailer Hitch for Ford Super Duty # RP30923 view full answer...
I really wish it did because we get these questions all the time. The B&W Patriot Slider item # BWRVK3270 won't work with the picture frame style adapters. It has to do with the spacing and also the height of the slider. The item # RP30156, and all of the similar designs from other competitors, won't let the hitch slide. We had one returned with a giant gouge in the steel. Another drawback to these type of adapters is they raise your hitch height almost 3" which pushes the nose of your... view full answer...
If you are carrying more than 500 lbs on the front of your F-350 then the only front mount hitch that will work is the EcoHitch item # 306-X7904. This hitch has a 1,000 lbs vertical load limit (tongue weight). The Curt item # C31078 only has a 500 lbs limit. Both are confirmed to fit a 2019 F-350.
I have linked an installation video below. I have also attached a picture so you can see what this hitch will look like once installed. view full answer...