If your 2012 Forest River Georgetown was built on a Ford F-550 chassis the SumoSprings I recommend are Custom Helper Springs # SSR-118-54 for the rear axle and # SSF-111-54 for the front axle.
These springs compress under loads to give you a smoother ride while also working to minimize the amount of back-and-forth movement you'll encounter. The springs will not require any type of drilling for the installation, and you will not have to perform maintenance on them; they simply replace your... view full answer...
I will be happy to provide you with the dimensions and hole spacing on the brackets included with trailer hitch # 41990-07 to see if it will work on your cab and chassis 2004 Ford F-550. I have included a picture with the measurements. view full answer...
We do indeed offer a replacement latch/hardware kit for your Stromberg Carlson # VG-97-2000 5th wheel tailgate as part # VG-2000-2197. If you needed the cables and set screw, you'd need # 2000-CB. The cable kits are sold individually, so if you need cables for both sides, you'd want to order two of them. view full answer...
We've got just what you're looking for. I'd recommend the Hopkins part # HM40975-11998. The included pigtail will wire up to the tow package harness under the truck as follows:
-Red Pigtail Wire to Left turn/stop which is typically a yellow wire in the vehicle harness
-White Pigtail harness wire is a ground connection
-Blue Pigtail wire carries output from brake controller, usually a blue wire in vehicle harness
-Green Pigtail wire to Right turn/stop which is usually a green wire in the... view full answer...
To stabilize your car trailer behind your Jayco Jayhawk I recommend the Blue Ox TrackPro Weight Distribution w/ Sway Control item # BLU36FR. This weight distribution system has built-in sway control that limits side-to-side movement of your trailer. It has a tongue weight range of 200 lbs - 600 lbs and a maximum capacity of 6,000 lbs. This will do a far better job of addressing stability when pulling a trailer than the Timbren Rear Suspension Enhancement System item # TFRSD you were looking... view full answer...
Based on the information you have provided, I see no reason why the Hopkins 7 Way Blade to 7 Way Round Adapter # 47595 would not work.
Another option would be to remove the 7-way round pin connector from your camper and replacing it with the Hopkins Endurance 7-Way Trailer Connect # HM48500. The mounting bracket, hardware, and grease packet are included and I have provided a link to the installation instructions for this product as well.
Regarding your question about a cover for your... view full answer...
We offer a range of trailer cargo control products including the versatile Erickson E-Track # E19146 for vertical applications that you referenced. These can be used with any of the E-Track strap products shown on the link at right, including the 12-foot ratcheting strap # EM59136. Other available accessories include spare tire mounts like # RA-16HST from RackEm. view full answer...
Depending on what cab style your 2006 Super Duty Cab and Chassis has will determine which DeeZee running boards you'd need. If you have a SuperCab you'd need the part # DZ15311A-15326, regular cab part # DZ15301A-15326, or crew cab part # DZ16421-16326. view full answer...
I reached out to Lippert and the discontinued Coachmen steps you have do not have replacement steps available. The only solution is complete replacement. I wasn't able to find the exact step you have since the part number corresponds with the control module, but I believe it is a single step on your 2006 Forest River Lexington GTS.
If it is a single step, you will be able to use the Kwikee Electric RV Step Complete Assembly # LC3691461 as a replacement. This step measures 24" wide. Typically... view full answer...
We have three plate-fin Derale transmission coolers confirmed to fit your 2000 Ford F-350 with the 7.3 L diesel. The best one for you is going to be the largest that you can fit in the front of your engine compartment so it gets as much air flow as possible.
All three for your truck are 11 inches wide a 7/8 inches deep. The difference is the height::
# D13502 is 7-1/4 inches tall
# D13503 is 8-3/4 inches tall
# D13504 is 12 inches tall
Each cooler will also need the Ford adapter fitting,... view full answer...
Sounds like you have a hitch mounted pintle mount like the part # C48190 and are looking for a hitch mounted platform like part # BWPMHD14005 for it to attach to. view full answer...
The overall width of the Buyers Products Class 4 Service Body Long Hitch Receiver # 3371801055 that you referenced 44-1/2 inches. I attached a picture that has that dimension and a few others listed as well. view full answer...
I spoke with my contact at Optronics about the Wishbone 4-Way Trailer Wiring Harness, # A20WB. They had documentation stating the green wire is 19 gauge and the yellow wire is 20 gauge. She could not state for sure what gauge the white and brown wires are but either 19 or 20. view full answer...
Yes, the Curt Trailer Hitch, # C15445, will fit on the 2004 Ford 350 Cab And Chassis. I have provided a link to installation instructions for you to review.
To complete your towing setup, you may want to consider the following items.
etrailer.com Ball Mount Kit, item # EBMK2416
Hitch Lock, item # e98880
4-Pole Hardwire Kit, item # 18252
Brake Controller Installation Kit, item # ETBC7
Brake Controller, item # 90195 view full answer...
I recommend the Timbren Rear Suspension Enhancement System # TFR350CC for your 2011 Ford F-350 cab and chassis frame. I checked with both Firestone and Air Lift and they both told me that they do not have an air bag set that is confirmed to fit with your vehicle.
The Timbren system is designed to assist your F-350's rear suspension with a weight capacity up to 6,000lbs. This will help to reduce rear end sag as well as provide additional stability while turning with heavy loads. You will... view full answer...
To add a 7-way into the bed of your 2006 Ford F-350 that has one at the rear of it you'd just need the # 41157 which was designed exactly for that. view full answer...
For your 2002 Ford E450 Shuttle Van I recommend the Draw-Tite Ultra Frame Service Body Trailer Hitch Receiver - Weld On - Class V - 2" # 41990-16. This trailer hitch receiver has a 16" drop and is rated for 16000lbs GTW and 1600lbs TW. This universal-fit trailer hitch will need to be welded to the frame of your vehicle.
If you're in need of a trailer connector then I recommend the Universal Installation Kit for Trailer Brake Controller - 7-Way RV and 4-Way Flat - 10 Gauge Wires # ETBC7.... view full answer...
The Curt Class V 2 Inch Hitch # C15445 is listed to fit a 2011 Ford F-450 Cab and Chassis with 34 inch wide frame.
I am sending a link to the installation instructions of the Curt hitch.
If you will be needing a pintle hook mount with a long shank I would recommend the Tow Ready Pintle Hook Mount # 63059. This mount will have a shank length of 11-3/8 inches from the center of the hitch pin hole to the end of the shank.
You will also need the pintle hook and ball combo that will bolt... view full answer...