It sounds like what you're looking for is the Camco Replacement Lid for Ventline and Elixir RV Roof Vents # CAM40161.
This replacement lid will work with your Elixir roof vent on your 1995 Northern Lite, is made from polycarbonate soo it's virtually unbreakable, and is a translucent white color so some light will be able to pass through. view full answer...
The reason you are having issues installing the Tekonsha Prodigy part # 90885 is because the correct install harness you need for your truck is the part # 3035-P and not the 3036. If you replace the install harness the brake controller will function again. view full answer...
We always recommend using the brackets and rails from the same company to ensure they are compatible. The bracket and rail kit we have for your 1993 Ford F-250 is part # RP30035. It includes the brackets, bed rails and all the nuts and bolts needed to install. I have included a link to the instructions below.
The kit you were looking at is for GM trucks. view full answer...
Yes, the Replacement Mounting Brackets # CARRBR14702K2 are the correct replacement brackets for the Carr Custom-Fit Side Steps # CARR102521, which is confirmed to fit your 1996 Ford F-250. view full answer...
I'm not able to access your shopping cart, but I am able to see the various products you checked out before you submitted your question, and I'd be happy to run through everything with you.
For a brake controller, the Tekonsha Prodigy P2, part # 90885 would be an excellent choice. The P2 provides safe and predictable braking in a unit that's easy to set up and easy to use. You'll need the # 3035-P brake control wiring adapter which will allow you to plug the controller in under the dash.
At... view full answer...
Your 1994 Ford F-250 2WD 8' bed with the 7.3 diesel will need one of two installation kits depending on if it has overload springs.
The B&W Turnoverball Underbed Gooseneck Trailer Hitch # BWGNRK1110 is for your truck if it has the factory overload springs. This kit will use the Installation Kit # BWGNRM1110 and Center Section # BWGNRC800.
The B&W Turnoverball Underbed Gooseneck Trailer Hitch # BWGNRK1100 is for your truck if it does not have the factory overload springs. This kit will... view full answer...
In order to have a wiring extension with 2 vehicle end connectors on it, you will want to create your own extension. We do not carry a pre-wired extension with 2 vehicle end 6-pole connectors.
You will want to use 2 of the Pollak 6-Pole, Round Pin, Trailer Wiring Socket # PK11609. These will need to be wired to either end of a length of 6-wire.
You can use the Deka Wire - Jacketed 6-Wire # DW04906-1. This wire is sold by the foot, so you can order the best length for your application.... view full answer...
We do not offer a custom-fit 5th wheel install kit for your 1995 Ford F350, but we do have a universal-fit install kit from Reese, part # RP30035. This kit includes universal under-bed brackets and their mounting hardware, as well as the above bed rails and the hardware required to mount those to the under-bed brackets. Drilling will be required to install this kit.
I confirmed with my contact at Reese that this kit is fully compatible with their Trail Boss 5th wheel hitches. It will work... view full answer...
I confirmed with Tekonsha that they do not offer a brake controller quick-connect harness for your 1993 Ford F-350 but you can still install their outstanding Prodigy P3 trailer brake controller # 90195. If you have a factory 7-way and the under-dash connection port you can make your own harness.
You can use the pigtail plug that comes with the P3 along with Curt harness # C51312. Simply cut off the black plug (which would normally connect to a Curt brand brake controller) and splice the... view full answer...
We can offer you two options in a universal 5th wheel install kit, part # RP30035 from Reese and part # HT31563-686 from Husky, both of which will require drilling into the truck's frame for installation. These industry-standard base rails will work with most hitches from Curt, Draw-Tite, Hidden Hitch, Reese, Valley and Husky. An installation video is linked for you.
A custom-fit installation kit is offered by B&W, their gooseneck/5th wheel base # BWGNRK1100-5W, which works with their... view full answer...
I have a great alternative for you. Unfortunately, the rails that fit the Thule TracRac SR # TH43002XT will not fit your 1996 Ford F-250 and F-350 with an 8-foot bed. However, a great alternative is the Erickson Truck Bed Ladder Rack w/ Load Stops # EM07705. The Erickson uses J-hooks that attach anywhere along the rails of your truck for an easy installation. The Erickson also comes with load stops to make sure that your cargo does not shift during transportation. All hardware needed for... view full answer...
The 12V power feed from a tow vehicle's 7-way connection passes enough current maintain a battery but not enough to charge a depleted one. Shore power and a 120V charger such as what you have is the right way to charge a discharged battery.
You can isolate your tow vehicle battery (and alternator) from power draw from the trailer battery by installing an isolation solenoid, part # PK5231201. This item uses any ignition-controlled circuit in the vehicle, such as the radio or power antenna,... view full answer...
5th wheel base rail installation kits include base rails, frame brackets and all required installation hardware.
The Reese 5th wheel base rail installation kit # RP30035 and 16K 5th wheel hitch # RP30047 are fully compatible with each other and with your truck. The base rail kit is the universal-fit type; these cost less but take longer to install due to the need for frame drilling. If you want to have the easiest base rail install use a custom kit # DM8552005-71.
For a wiring harness... view full answer...
The Curt T-Connector 4-Pole harness you referenced, # C55316, is a correct fit for your 1994 Ford F-250 and plugs in to a factory connector at the rear bumper to provide basic lighting functions for your trailer.
If your truck does not have a factory 7-way trailer connector you will need to have this working 4-pole connector in place to install one for use with a brake controller. You will also need a trailer brake controller, such as the reliable and popular Prodigy P2 # 90885, as well... view full answer...
The B&W Turnoverball Gooseneck Custom Installation Kit for Ford # BWGNRM1110 is the correct kit needed for your 1996 Ford F-350 with overload springs.
This rail kit will let you install your B&W Turnoverball gooseneck trailer hitch # BWGNRC800. The rails have a sturdy steel construction and has a powder coated finish that resists corrosion.
I attached an installation video link below. view full answer...
When looking at Weight Distribution (WD) systems you will want to find one that has a range that your Total Tongue Weight (TTW) falls in the middle of.
To find your TTW you will need to add the Tongue Weight (TW) of your loaded and ready- to-go trailer plus the weight of any cargo behind the rear axle of your 1995 Ford F-250/F-350. Keep in mind that your TW should be 10-15 percent of the weight of your trailer. Since 10 percent of your GVWR of 9680 is 968 and the Equal-i-zer Weight Distribution... view full answer...
The correct CIPA slide on mirrors that fit your customer's 1995 Ford F-350 depend on which mirror style the truck has. Take a look at the pictures I attached.
If the truck has the mirror in picture 1 use part # CM11000-2
If the truck has the mirror in picture 2 use part # CM11500
Both mirrors include both the driver and passenger sides. view full answer...
To add a 7-way to your 1996 Ford F-350 you will want to install the 7-Way Pre-Wired Car Connector # 20023, which is a confirmed fit for your truck. I've added a link to a help article on trailer wiring which details the functions of the connector. This will be a hard wire application and includes the installation instructions. As for an isolator I believe you are referring to a solenoid. For that you want the Battery Isolation Solenoid # PK5231201 which is going to switch off your F-350's... view full answer...
We have the perfect replacement hub for your trailer with a bolt pattern of 5 on 4-3/4 inches!
The Trailer Hub and Drum Assembly # AKHD-5475-35-K is rated for a 3,500 pound axle and has a sturdy iron construction and is compatible with both electric and hydraulic drum brakes.
The hubs have an Inner Bearing # L68149 that has a 1.378 inch inner diameter and an Outer Bearing # L44649 that has a 1.063 inch inner diameter. If the bearings listed above please reach back out to me and I will... view full answer...
The yellow wire on the Hopkins 7-Way RV Style Connector with Molded Cable # H20046 will not be able to charge an on-board battery, it should really be used for reverse lights. To charge the auxiliary battery on your trailer the best option is to use a battery charger such as the CTEK MULTI US 3300 12-Volt Universal Battery Charger # CTEK56353 which you would plug into a standard outlet.
You can maintain that charge when driving by running # 10-1-1 wire along with 40 amp circuit breaker... view full answer...
Go To Results