Since your 2018 GMC Canyon already has the needed brake controller wiring ran up under the dash (which indicates that you have the factory tow package), a separate 20 amp fuse isn't needed when hooking up a brake controller like the Tekonsha Primus IQ # TK90160. As you mentioned, a 30 amp fuse is already installed in-line on the truck for this protection.
The pigtail wiring from the controller will splice directly to the wiring under the dash. On the brake controller the blue wire is... view full answer...
Adding air to the Reese Goose Box 5th-Wheel-to-Gooseneck Air Ride Coupler Adapter # RP85FR is a fairly straight-forward procedure but there are some steps you need to take to add the air. Attached is a clip from the linked instructions but I am adding the text here as well:
1. Perform the hitching procedure before adjusting suspension air pressure, with the trailer loaded.
2. With trailer hitched to truck and landing gear / jacks retracted, add air to the air bag fill valve shown in figures... view full answer...
The Dexstar Conventional Steel Wheel part # AM20766 is lug piloted which means the wheel is centered and supported via the lug nuts/studs. If you are looking for a wheel that is centered and support via the pilot hole then that would be referred to as hub piloted. The trailer hub will dictate whether you need lug or hub piloted wheels but they are not cross-compatible. That said, lug piloted is the most common and likely what you have now. view full answer...
Some trimming of the rear fascia on your 2020 Honda CR-V is indeed required when installing the etrailer Trailer Hitch Receiver # e98848 to allow clearance for the drop-down receiver. You will just need to use some shears/snips to trim about 3" x 1-3/8" section from the bumper, as shown in the attached image from the install manual.
This trimming is what allows the hidden-crosstube appearance of the hitch where only the 2" receiver is actually visible. I have attached a full installation... view full answer...
The Kat's Heaters Thermostatically Controlled Circulating Tank Heater part # KH13150 will automatically turn off when the coolant temperature reaches 175 degrees Fahrenheit. view full answer...
The most similar actuator replacement for the now discontinued Atwood units is the Demco part # DM72VR that you referenced. The bolt holes are close enough to match up. The small difference in height would not be an issue as the bolts will still line up properly. view full answer...
You do not have to turn off the electric sway control of your 2019 Ford F-150 when using a weight distribution system like the Equal-i-zer part # EQ37121ET that you referenced. The two will work great together. view full answer...
Since the nylon brC13406 hitch installed, the next thing I'd try is giving those threads a complete soaking in a spray lubricant like Kroil, WD-40 or PB Blaster, and giving them a good scrub with a wire battery terminal brush like what's included with # DW00254. Spray the threads down, let it sit for a few minutes then give it a good scrub. You might need to repeat this procedure a few times.
If that doesn't do the trick, you'll need to bust out the nuclear option by using an M1 x 1.25... view full answer...
You can indeed. Both the 7-way and 4 pole connectors are capable of being used simultaneously.
I've linked you to a product demonstration video featuring the Hopkins # HM40950 7-way/4-pole connector. view full answer...
The actual position of the bed rails can vary according to which manufacturer's frame bracket you're using.
Since most folks tend to order the brackets from the same manufacturer as the hitch, I'll assume unless told differently that you're using the Curt # C16428 frame brackets with your Curt bed rails (you always want to ensure that the frame brackets and bed rails are from the same manufacturer so the capacity of the installation isn't compromised). The rails for this kit mount so that... view full answer...
The easiest way I can show you how to install the Curt trailer wiring harness # C59236 on your 2018 Ford EcoSport is by having have you check out the install video I attached for this on a 2018 EcoSport just like yours. view full answer...
In order to install the Curt Spectrum Trailer Brake Controller part # C51170 on a 2019 Toyota Tacoma on a you'll need to use the Curt Custom Wiring Adapter for Trailer Brake Controllers part # C51455. The plug that this adapter harness will attach to will be rectangular in shape with four pins inside.
In regards to hardwiring, it for one does not sound like you have the correct plug but that said you'd need to test the pins anyhow as I wouldn't have any sort of pin out diagram to go off of. view full answer...
Installing the Rhino-Rack Heavy-Duty Bar Roof Rack for Camper Shells # Y01-140B is pretty straightforward in that you will install the rails by using a 6.5mm drill bit to drill holes in your roof and then after that it's a simple manner of securing everything down with the included parts. We do recommend using some form of sealant like the TremPro 644 # 0160297 to help keep water out of your camper shell.
We don't have any installation videos at this time, but we do have the installation... view full answer...
The best way to find a place to install a hitch like the Draw Tite part # 76419 on your 2019 Chevy Equinox will be by finding a local garage to you with a good reputation. Hitch installs are pretty basic for most installers so any mechanic with a solid reputation will have no problem at all. We don't have a list of installers we can point you towards though. view full answer...
The WeatherTech cargo mat part # WT40608 is a confirmed fit for your 2019 Hyundai Santa Fe XL and goes all the way up to the back of the second row of seats. This could easily remove to access the third row area, or you could go with the part # WT40609 which butts up to the back of the third row seats instead. view full answer...
The Blue Ox Avail Tow Bar - Motorhome Mount - 10,000 lbs # BX7420 will automatically extend to a rigid point for safe towing. The hitch pin holes don't dictate a safer towing option, so the two pin holes will be equally safe and there are two options to simply help with folding clearance if you have a spare tire like shown in the attached video. If it were me, I'd put as much of the shank in the receiver as possible to still give you the needed bumper or spare tire clearance. view full answer...
We've actually had this one asked before and have consulted with MaxxAir. Even though you can technically install the MaxxFan Deluxe Roof Vent # MA00-06401K wired to a separate switch, it is not recommended. The reason for this is that their fans are designed to have a constant 12V feed, and when an external switch is used there will be a short spike in voltage every time the switch is turned on, which over time could potentially cause issues with the circuit board on the vent.
Additionally,... view full answer...
On the 2006 Infiniti FX-35, the Thule Gateway 2, # TH88VR, will fit. The lower clips will fit in the bottom edge of the trunk/hatch. The top clips will fit in the gap at the front edge of the top of the trunk/hatch. The lower arm of the rack will rest in the area between the license plate well and the upper tier of the bumper. I have included a link to a video review of this series of bike racks for you to view.
To carry women's bikes or bikes with sharply angled top tubes or step-through... view full answer...