When adjusted so it's at its maximum drop, the B & W # BWTS10040B Adjustable Ball Mount measures 7 inches from the inside top of the receiver to the base of the trailer ball, at maximum rise, the height difference is 7-1/2 inches as shown in the photo I've edited for you. view full answer...
The diameter of the shank is 2-5/8-inches on Curt Replacement Ball for Curt Double Lock Flip and Store Gooseneck Hitch # C60616. This is true also for their offset ball for this system, part # C602. view full answer...
The Yakima EXO SwingBase 2 Tier Swing Away Hitch Extender # Y82VR is 29" from the center of the hitch to the locking handle on the base. The locking locking handle does sit 8" above the top of the receiver which you will want to ensure that your door will also clear if the door does sit inside the 29" measurement of SwingBase.
Be sure to get the License Plate and Tail Light Relocation Kit # Y74VR as with your gear loaded it will most likely impair the view of the tail lights on your van. view full answer...
The Reese Quick-Install Custom Bracket Kit for 5th Wheel Trailer Hitches that you referenced, part # RP50082, is designed specifically to fit Ford trucks and install without drilling by using the existing holes in the Ford frame. This bracket kit will not fit on your 1997 Dodge Ram 2500.
We do offer a universal base rail installation kit for your 1997 Dodge Ram 2500, part # RP30035 from Reese. This will fit both 6-foot and 8-foot beds and is compatible with several brands of 5th wheel... view full answer...
The Air Spring # AL50217 has a design height of 5-1/2". This is the height the air spring is designed to have between the mounting brackets at stock, unloaded weight. view full answer...
I spoke with my contact at Truxedo and she said the Replacement Truxedo Shur-Bond Velcro Brand Fastener, part # TX1115174 is 80 inches long by 1-5/16 inches wide. This part contains 2 fasteners. view full answer...
Happy to help! The Lockrack Adjustable Watersport Carrier item # LR24VR only fits one kayak so you would need two of them. They measure anywhere from 23-3/4" wide to 43" wide depending on how wide your kayak is. You would need to take some measurements of your kayaks to see if you would be good with the standard 59" Rhino-Rack Vortex Aero Crossbars item # RRVA150B-2. Or needed to go with the longer 65" Vortex Aero Crossbars item # RRVA165B-2.
Here are the other parts you'll need to add... view full answer...
The shank length on the Tow Ready Interchangeable Hitch Ball Set # 63803 is 2-3/8 inches. I have linked a video review of this ball set for you. view full answer...
Optronics uses candelas to rate the brightness of their lights instead of lumens and the output of the Optronics 6-1/2 inch Oval LED Back Up light, # BUL52CB, is 175 candela. At a distance of 1 foot, the candela output is equal to the output in lumens.
The next brightest 6-1/2 inch oval light would be the part # BUL22CB which has an output of 160 candela.
The part # BUL10CB that you referenced has a candela rating of 125 which would make it the dimmest offering which I would not recommend... view full answer...
In regards to the Ranch Hitch Universal 5th-Wheel-to-Gooseneck Coupler Adapter part # AM3100, the bolt circuit diameter is about 8-5/8" on center whereas the overall diameter of the plate is about 9-3/4". I will say that most pin boxes are 12-12-1/2" wide so you should not have to worry about there not being enough space on the skid plate of your pin box.
I have attached a photo for you with the above dimensions. view full answer...
The 7" Weld-On Bracket Kit part # 4907 which is designed to be used with the Draw-Tite Ultra Frame Service Body Trailer Hitch Cross Tube part # 41990 or part # 41991 has two plates which are each 3/8" thick. There is also the 16" Weld-On Bracket Kit part # 4916 available which has side plates that are 3/8" thick as well. view full answer...
The actual distance of the wiring harness portion of the Hopkins # HM42190 is 7 inches. The distance from the back of the 7 way to the end of the plug is 9 inches.
I also checked the length of the Tow Ready Harness # 20135. This has a 4-way on it as well as a 7-way, but it is a bit longer than the Hopkins. The Tow-Ready harness portion is 11 inches long. I also have a picture attached with the dimensions noted.
I have also included this information in the brief video attached. view full answer...
I went out to our warehouse to take a look at the Lippert Components Inner and Outer Entry Door Frame # LC363370 referenced in your question. I measured an inside channel dimension of right at 1 inch. I have attached an image with this dimension labeled that you can also take a look at.
This is a 12 inch x 21 inch inner and outer entry door window frame that is for use on LCI Radius RV Entry Doors. I have included a short video demonstration on this product for you to check out as well. view full answer...
The distance from the hitch pin hole to the center of the hitch ball of the Curt Rebellion XD Shock Absorbing Adjustable Ball Mount # C57UR that you referenced is 13-1/4 inches. view full answer...
There are 2 sets of holes on the Reese adapter # RP30154 for Rams with the OEM prep package. The outside set of holes is 29 inches apart on center and the inner set is 20-1/2 inches apart on center. Front to back they are approximately 22 inches apart on center. Any Reese, Draw-Tite, Curt, Valley, or Husky 5th wheel trailer hitch that fits in above the bed rails will fit in this adapter. I have included a link to the installation instructions for you. view full answer...
I went out to the warehouse and pulled the Cipa Towing Mirror, # 10300, for the 1996 Dodge Ram. From the edge of the housing where the factory mirror will be to the edge of the glass at the furthest out point measures 5 inches.
The overall length including the housing is 15-1/2 inches. The glass itself measures 5-1/2 inches tall by 4-1/4 inches wide. I made a video for you showing the dimensions. view full answer...
You are half way there! Simply measure from the top of your receiver down to the ground. The difference between that measurement and the 18-1/2 inches from your trailer coupler to the ground would be the rise or drop you would need. For instance, if the distance from the top of the receiver tube to the ground was 21-1/2 inches, the difference between that and your coupler height would be a drop of 4 inches. If this is the case with your truck, a ball mount with a drop of 4 inches like part... view full answer...
I reached out to the manufacturer who told me the frame brackets on the Curt Quick Goose 2 Gooseneck Hitch with Installation Kit for Dodge Ram # C640-635 measure 1/4" thick.
This gooseneck hitch has a 30,000 lb capcity and the ball is hidden when not in use to give the truck bed of your 1997 Dodge Ram a clean look; additionally, this gooseneck hitch will fit both 6-1/2' and 8' beds. view full answer...