Please see the following for your requested measurements on the Non-Mortise RV Cabinet Hinges, # 37270635.
The width of the hinge opened is 2-3/8" and the width of the hinge closed is 1-3/8". and just in case, mounting hole distances are, the two furthest mounting hole from the top of the hinge to the bottom hinge measures 2-1/2" center on center while the holes on the middle hinge are 7/8 of an inch center on center. view full answer...
The thickness of the Alpha Systems Superflex TPO RV Roof Membrane - Gray - 380 Sq Ft Item # AL75CV is 0.030" (0.76mm) which is comparable to the thickness of a credit card. view full answer...
With you having 2- 3500lb axles your maximum capacity is 7000lbs evenly distributed over both axles. With the trailer weight of 8240lbs you definitely risk damaging the axles, suspension and other parts of the trailer.
Trailer Axles will sometimes have a natural curve in them but if overloaded they will bend more causing the tires to wear unevenly.
If you can get me the information off the axle data tags I can help you to identify the correct replacement axles. You will also want to... view full answer...
The Replacement Velcro for TruXedo Tonneau Covers part # TX1705183 measures 3' long x 1.348" wide. It is designed for the LoPro QT, Edge, Deuce 2, Prox-15, and TruXport covers. view full answer...
On your 2019 GMC Acadia, there are many roof racks rated for 120 lbs and up to 165 lbs. According to the online owners manual the roof structure can support 220 lbs, so you will be limited by the roof rack itself.
I recommend the Rhino-Rack Vortex Aero Crossbars # RRVA118B-2 with Rhino-Rack SX Series Legs # RRSX100. This rack is rated for 165 lbs. view full answer...
The inside diameter of the portion of the handle that fits into the jack, is approximately 1/2 inches, while the outiside diameter is closer to 13/16 inches. The etrailer Crank Handle # RVLG-HDL is designed to be used with Landing Gear Set # RVLG-8000. view full answer...
The overall length is 2-3/4 inches, and the diameter is 5/8 inches of the Replacement Secondary Pull Pin Assembly # 8880530.
This is a direct replacement for the Yakima TwoTimer and Yakima FourTimer bike racks. view full answer...
We do have a bike cover for your e-bikes, though the Swagman S82006 has been discontinued. The new bike cover is the one you mentioned:
- Swagman Bike Cover for RVs - Large - 2 Bikes # S24FR
This cover is designed to be larger than the 82006 and made purposefully for use with electric bikes and cruiser bikes which have become so popular, so it will work as a cover for your e-bikes without issue. I have added a link below to a video review of the # S24FR which I recommend checking out... view full answer...
The small door in the front of the Valterra Electrical Cable Hatch for RVs does measure 1 inch by 1 inch, and is designed to work with a max 50 amp cable so you'll just want to ensure your cable is no more than 1 inch in diameter and it will fit. The hatch is available in both white and black:
- White: Valterra Electrical Cable Hatch for RVs - 5-3/16" Diameter # A10-2135VP
- Black: Valterra Electrical Cable Hatch for RVs - 5-3/16" Diameter # A10-2135BKVP
I have added links below to video... view full answer...
When there is a tire with low pressure or any other anomaly there will be an audible alert combined with flashing messages to let you know what the problem is. Whether it's high/low pressure, high temperature, or fast leak. It will then tell you which tire is the issue as well as it will be flashing on the display which shows each of the tires represented around the main display. view full answer...
Based on the sticker and weight ratings showing it would be a class III hitch. The difference between a class III like the Curt Trailer Hitch Receiver Item # C13903 and IV hitches like the Curt Trailer Hitch Receiver Item # C14002 is typically the weight ratings. The hitches we offer for the 2012 Ford F-150 are class III and IV. The Class IV has a 1000lb tongue weight and a 10000lb towing capacity and when used with weight distribution goes up to 1200lb and 12000lb. Our Class III hitches... view full answer...
While the Tow Ready Base Rail Lock part # TR63254 doesn't have a stated weight capacity Tow Ready has stated that it will match the weight capacity of any hitch used in the OEM rails. view full answer...
On a 2012 Subaru Outback Wagon Draw-Tite trailer hitch # 75673 measures 5-1/4 inches from the center of the hitch pin hole back to clear the bumper on a 2012 Subaru Outback.
We have not installed the Curt hitch # 13390 on a 2012 model. But on a 2011 it measured 3-1/2 inches, on a 2014 it was 3 inches, on a 2015 it was 3-1/2 inches, and on a 2010 it was 4 inches. Based on all of this information it would seem the Curt hitch would be the best option. The only catch is that Curt says you... view full answer...
I pulled one of the Roadmaster BrakeMaster systems, part # RM-9060-900002 from our warehouse and took some measurements you requested.
The air compressor housing measures 10 inches wide at the front, 8 inches deep, 10-3/4 inches tall and the width including the mounting flanges on the back of the housing is 12 inches. This system is designed to work with RVs that have hydraulic brakes. It includes all of the hardware and installation instructions. view full answer...
I have a seat cover that will work great but there are no custom fit options for bench seats on your Pleasure-Way Plateau Motorhome. I recommend the Aries Automotive Seat Defender Bench Seat Protector item # AA3147B. This black cover is 63" wide x 58" tall. It has two covers that go over the headrests with hook-and-loop straps. It also has cutouts that will open so you can access any seat belts.
I have linked a review video below so you can see what this cover looks like and how to set it up. view full answer...
We have the Amber LED Trailer Clearance and Side Marker Light item # MCL52AB and the stainless Steel Trim Ring item # A3TRSSB. We do not have a chrome flange though or those two parts available in a set. view full answer...
The center of the hitch pin hole for the Draw-Tite Max-Frame Trailer Hitch Receiver # DT37GR is 6" further out than the center of the hitch pin hole for the Curt Trailer Hitch Receiver # C76WR. Since the hitch pin hole determines where your accessory will be sitting this is the dimension you want to take note of as opposed to the end of the receiver tube.
I went and measured the Curt hitch and from the outermost mounting plate that installs on your 2022 Ford Bronco to the center of the... view full answer...
Yes, the Gen-Y Adjustable 2-Ball Mount w/ Stacked Receivers # 325-GH-924 can be used to mount your debris loader and tow your landscape trailer. This ball mount will not decrease the capacity of your hitch and it is more than capable of handling the weight of both.
This ball mount has a maximum rise and drop of 6" with an overall height of 12-1/2". It features a zinc primer and powder coat finish, and is made in the USA. If you would like locking hitch pins to keep everything secure you... view full answer...
Swagman actually has a very similar bike rack to the one you referenced that was setup for carrying heavier e-bikes with the E-Spec part # S94FR which has a 70 lb per bike capacity. This is going to be your best option and will work great for you. view full answer...