Expert Answers about Chrysler 300

Recommended Trailer Hitch and Parts To Tow a Trailer with a 2008 Chrysler 300
The Draw-Tite Max-Frame Trailer Hitch Receiver part # 76145 is what I recommend for a 2008 Chrysler 300. It has a class III rating with 2" receiver tube opening which will allow for a greater towing capacity and more ball mount options to choose from when compared to the other class II, 1-1/4" receiver tube options. In order to complete your towing setup you'll need a wiring harness, the Curt T-Connector Vehicle Wiring Harness with 4-Pole Flat Trailer Connector # C55546 and a ball mount/hitch...
view full answer...

Solution for Roof Rack for 2017 Chrysler 300
I do have a solution, but Inno has discontinued the fit kit for your 2017 Chrysler 300. Unfortunately, other fit kits will not allow you to install this roof rack on your vehicle. What I can offer instead is a Yakima roof rack like the CoreBar rack, which is similar to the # INXB108-115. You will need the following parts to complete the rack: -Yakima CoreBar Crossbars # Y00421 -BaseLine Towers # Y28TR -BaseClip Fit Kit # Y06110 The Yakima JetStream crossbars # Y00425 will work with...
view full answer...

Why is Weight Capacity of Trailer Hitch Receiver Confirmed to Fit Greater Than Vehicle Tow Rating
The Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" # C13093 is a confirmed fit for your 2016 Chrysler 300 and is also a fit for a few other models like the Dodge Charger and Dodge Challengers of certain model years. The towing capacity of your vehicle is 1000 lbs as you mentioned, and it is not uncommon for trailer hitch receivers to be rated much higher than the vehicles they are made to fit. This is the case of your vehicle and hitch receiver but the hitch manufacturers...
view full answer...

Does MagnaFlow Exhaust Restrict Air Flow on a 2014 Chrysler 300S V6
The MagnaFlow exhaust system # MF15119 for your 2014 Chrysler 300S V6 does not restrict exhaust flow. If you used the same configuration with the stock exhaust parts on the vehicle then that would restrict it some. But the MagnaFlow mufflers have no baffles, chambers or louvers and the pipes maintain the same diameter in the bends allowing the exhaust to flow more freely through the system.
view full answer...

2007 Lincoln Navagater to carry a power chair on carrier about 420 Lbs
You are correct. The RoadMaster 4 Inch Hi-Lo Drop, part # RM-070 is meant for use with a tow bar used for towing a vehicle. It is meant to tow a rolling load, not a situation where more than 100 lbs of downward force is applied to it.
view full answer...

Concealed Trailer Hitch for 2020 Chrysler 300
I can understand wanting to keep the appearance of your 2020 Chrysler 300 as clean as possible, and the perfect trailer hitch for your car is the Draw-Tite Trailer Hitch Receiver # 36548 because it has a concealed crosstube with only part of the receiver showing, as you can see in the accompanying photo of this hitch installed on a Chrysler 300. This hitch has a 1-1/4 inch receiver will be a perfect hitch for a bike rack such as Hollywood Racks Trail Rider 2-Bike Platform Rack # HR200Z...
view full answer...

Hitch Mounted Bike Rack Carrier And Receiver For a 2019 Chrysler 300S E-Bike Weighing 70LBS
For your 2019 Chrysler 300S you will need to check your specific vehicle to determine if your drivers side muffler can be removed. I was unable to find a direct answer from Chrysler as to if this was model year or trim specific. The Curt Trailer Hitch Receiver # C13093 does recommend removing the drivers side muffler to install it but like the other receivers if you have a welded on muffler you can remove the rear fascia to install the receiver. We have added a new feature to our website...
view full answer...

How to Determine Which Ball Mount Will Have Enough Rise for Curt Hitch on a 2005 Chrysler 300c
The best way to determine which ball mount is right for your 2005 Chrysler 300c and your trailer is to take a few simple measurements. Since you don't have the hitch we can see by the video of the Curt # 13465, I've attached, that the hitch receiver is going to be 10-1/4 inches from the ground. You will then want to take a similar measurement from the bottom of the coupler to the ground. Then compute the difference. If the hitch height is greater than the trailer height, then •hitch...
view full answer...

3 Bike Platform Bike Rack Recommendation for 2007 Chrysler 300
For a 3-bike platform rack the Kuat Transfer part # KU24FR would be a great option. We had the chance to test fit this rack on a similar 2015 Chrysler 300 and it fit and worked well. Check out the review video I attached that shows this. Platform bike racks are normally really heavy, especially ones that carry over 2 bikes like this one. The Transfer is relatively light all things considered at 51 lbs. Most similar racks are near 100 lbs. If you are in need of a hitch you'll want the 2...
view full answer...

Will the Saris Bones fit my 2017 Chrysler 300S with Spoiler?
I checks Saris's web site and they do confirm the fit for the Saris Bones 3 Bike Carrier part # SA801BL on your 2017 Chrysler 300S.
view full answer...

Distance Between Bolt Holes On Draw-Tite Hitch for a 2018 Chrysler 300
In regards to the Draw-Tite Max-Frame Trailer Hitch Receiver part # 76145 which is a confirmed fit for a 2018 Chrysler 300 (All Models), the mounting holes are about 41" apart on center which I think is what you are asking for. If not, please just let me know but I have also attached a dimensional drawing for you as well.
view full answer...

Availability of a Folding Cargo Carrier To Fit a 2008 Chrysler 300 and Carry a 19 By 40 Inch Scooter
The closest match for your 2008 Chrysler 300 that we have is the Draw-Tite Hitch Cargo Carrier, item # 6502. This carrier has a 20 inch by 48 inch deck and will handle up to 500 pounds. You will need to check the tongue weight capacity of your vehicle and hitch to be sure it will be able to carry the weight of your scooter and the weight of the cargo carrier at the rear of your car. You will also need to measure the distance from the center of your hitch pin hole out to the farthest part...
view full answer...

Is the Four Pin Brake Controller Connector Installed Under the Dash on All 2004 Ford Explorers
The Hopkins Plug-in Simple Brake Wiring Adapter - Ford, item # HM47715, will only work on Ford Explorers that have the factory installed 7-Way connector at the rear of the vehicle. Since your vehicle has a 4-Way flat connector at the rear of the vehicle you will need to do some extra wiring to install a brake controller. The easiest way to wire a brake controller on your Explorer is to use a brake controller installation kit, item # ETBC7. You will need to plug the connector into the...
view full answer...

Does Tekonsha Trailer Wiring Harness 118658 Fit 2019 Chrysler 300C
I checked with Tekonsha and they list the trailer wiring harness part # 118658 as a confirmed fit for all models of the 2019 Chrysler 300 so that would also include your 300C.
view full answer...

Roof Vent for a 1968 Streamline Travel Trailer
We have several vents that might work for your Streamline trailer but nothing that is made specifically for it. I have included a link to the right to the options for you. Most of the vents require a 14-1/4 inch square opening to install the vent. The majority of the vents have plastic lids with a few exceptions that have metal lids. Beyond that it is just a matter of the color you want: white, blue, smoke, silver, clear, and metal. I also recommend the vent installation kit # 344270KITW.
view full answer...

Will DeeZee Universal-Fit, Brite-Tread Mud Flaps, # DZ1808 Fit a 2008 Chrysler 300 without Drilling
The DeeZee Universal-Fit, Brite-Tread Mud Flaps, # DZ1808, are a universal fit item so fit guide information for specific vehicles is not available. You can measure your 2008 Chrysler 300 to see if they can fit. The flaps are 11 inches wide at the widest point and 19 inches tall at the tallest point. If you determine that the mud flaps will fit, there is drilling required. Once you have aligned the flaps in the desired location, you will need to drill 3 holes through the flap and wheel...
view full answer...

Will Curt 20x60 Folding, Aluminum Cargo Carrier, # C18100 Fit a 2008 Chrysler 300
You will need to measure from the center of the hitch pin hole out to the distance required to clear the rear of the vehicle on your 2008 Chrysler 300. We have two videos that show this distance is 8 inches with a Class III trailer hitch installed but you will need to verify on your actual vehicle. I went out to the warehouse and assembled a Curt 20x60 Folding, Aluminum Cargo Carrier, # C18100, to measure it. In the folded position, it measures 5 inches from the center of the hitch pin...
view full answer...

Recommended 4-Way Wiring Harness for a 2019 Chrysler 300
Kayak trailers usually have a 4-way connector because they're not heavy enough to require brakes. To add a 4-way connector to your 2019 Chrysler 300 you will want the Curt T-Connector Vehicle Wiring Harness item # C56235. This wiring harness is custom fit and plugs into existing wiring behind your rear tail lights. I have linked an installation video below that will show you how to set this harness up. I have listed some other parts you will need to tow a trailer with your 2019 Chrysler...
view full answer...

No Brake Lights when Towing New Wheelchair Trailer With 2007 Chrysler 300 Wiring # 118404
Your 2007 Chrysler 300 has a 2-wire system that combines the brake light and turn signal function onto one circuit. This means that if the brake and turn signals on the car are working correctly, the brake signal at the trailer connector should work properly, as long as the wire harness connectors and wires are connected properly and there is no damage. The first thing to do is confirm or eliminate the wiring harness as the problem. Disconnect the trailer and test the 4-Way connector with...
view full answer...

Troubleshooting Curt Trailer Wiring Kit # C55546 Not Active After Install
Check to make sure the fuse is in the fuse holder of the Curt trailer wiring kit part # C55546 as well as the white wire is grounded properly. Typically when this problem arises the issue is the fuse not being installed.
view full answer...