Sounds like the carriage bolt hasn't slid all the way down into the carriage bolt block and that is why it is just turning. You have to pull the bolt all the way through the block so that the square shoulders of the bolt slides into the square hole of the block. view full answer...
With the Curt Trailer Hitch Receiver # C11133 on your 2013 Chrysler 200, Curt recommends using one of the following ball mounts.
First is the Curt Class II Drawbar # C45522 with either a 1-7/8" Ball # C40001 or 2" Ball # C40018. Or you can choose one of their Euro Style Ball Mounts with a 1-7/8" # C45591 or 2" # C45592 ball. Whichever you choose you will need a Curt Hitch Pin and Clip # F-4 to secure it in your receiver.
You will also need a Vehicle Wiring Harness # C56211 to control... view full answer...
For a trailer hitch for your 2012 Chrysler 200, I recommend the Draw-Tite trailer hitch # 24871 because it does not require the use of a stabilization strap for non-trailer loads like the Curt hitch does. I have included a link to the instructions and a video showing a typical installation for you.
Because this is a Class I trailer hitch there are only certain bike racks that you can use. The HitchSki, # Y02418, only fits on certain Yakima 4-bike racks, none of which will fit in a Class... view full answer...
Your 2013 Chrysler 200 has the transverse Pentastar 3.6 liter which Kat's recommends their heater part # KH11814. The cartridge location you need to use is right behind the engine block on the driver side. So the side of the engine that faces the firewall and all the way on the driver side. view full answer...
The Curt hitch part # C11133 that you referenced has been confirmed to fit the Sedan and Coupe models of the 2013 Chrysler 200 so it should work well for you.
I attached an install video for you to check out as well.
The Curt hitch comes with the correct ball mount, hitch pin, and clip. For a ball you can use # 19256 for 1-7/8 inch diameter or # 19258 for a 2 inch diameter.
For trailer wiring, use Vehicle Wiring Harness # C56211. I have included a link to the installation instructions... view full answer...
Yes, trailer hitch # 24919 will fit your 2015 Chrysler 200 S. I have linked a video showing an example installation for you.
The appropriate ball mount is # 3593 if you plan on towing. For a 1-7/8 inch ball I recommend # 19256 and for a 2 inch ball I recommend # 19258. And for trailer wiring I recommend # C56242 to add a 4-Way flat to the rear of the vehicle.
If you want to use the hitch for an accessory such as a bike rack or cargo carrier then you have to make sure the accessory is... view full answer...
For the 2012 Chrysler 200 with a bare roof, I would install the Inno Roof Rack which uses part numbers # INB127, # INSUT, and # INK600. This is the most affordable roof rack for this vehicle and would work well with a kayak carrier such as etrailer J-Style Kayak Carrier # e98878. This J-style kayak carrier offers a simple tool-free installation and comes with all the straps necessary for securing your kayak. I attached a couple demonstration videos for you to check out. view full answer...
Currently our Curt Drawbar # C45028 has the most rise available for a 1-1/4" Class I receiver like that you would have on your 2015 Chrysler 200. The rise is 5-3/8" from the receiver.
To get slightly closer to your 6" rise you can use a Curt Class I Drawbar # C45025 with a Curt RockerBall Shock Absorbing 2" Hitch Ball # C94CR. The ball mount has a rise of 5" and the RockerBall sits 1-1/2" higher than a traditional 2" ball. As long as your trailer accepts a 2" ball this would give you... view full answer...
The most popular hitch for a 2013 Chrysler 200 Sedan or Convertible is the Curt Class I trailer hitch # C11133.
I wouldn't recommended using a cargo carrier to carry an electric wheelchair with a Class I hitch because your maximum tongue weight is 200 pounds. Based on the wheelchair carriers weighing roughly 90 pounds and electric wheelchairs around 200 pounds it will exceed the 200 pound maximum tongue weight.
The best option to carry the electric wheelchair is by a trailer because... view full answer...
For your 2011 Chrysler 200, we have a confirmed fit for both the Draw-Tite Sportframe Trailer Hitch Receiver # 24871 and the Curt # C11133. The Draw-Tite hitch will be recessed too far under your bumper for a cargo carrier, so I recommend the Curt hitch which will require stabilizer strap # 18050 and has a measurement of 4-1/2 inches from the center of the hitch pin to the outermost part of the bumper. You will simply need a Class I rated cargo carrier with the closest part of the rack... view full answer...
There is an underbody panel that will need to be trimmed or removed to install la hitch on a 2015 Chrysler 200 but no bumper fascia trimming.
I recommend Draw-Tite trailer hitch # 24919. It is the most popular option for your 200. I have linked the instructions for you to view.
If you want to use the hitch for an accessory such as a bike rack or cargo carrier then you have to make sure the accessory is rated for use with a Class I trailer hitch. Also, with a bike rack, you are limited... view full answer...
I did check with Roadmaster and the Roadmaster EZ4 Base Plate Kit # RM-52297-4 that you referenced is only a fit for the sedan version of the Chrysler 200. It will not work with the 200 convertible.
At this time there is not a custom base plate kit available for your 2012 Chrysler 200 Convertible.
You may be able to go with a universal base plate kit like the Blue Ox # BX88230. Most bumpers do need to be reinforced or modified for proper installation, as the brackets need to mount to... view full answer...
The installation instructions for the Curt Class I receiver # C11133 specifically mention the procedure for installing the hitch on dual exhaust-equipped vehicles, to the hitch is indeed compatible with your vehicle.
The procedure specific to dual exhaust vehicles is mentioned in step one of the instructions, which you can see by clicking on the link provided. view full answer...
We've spoken with Draw Tite before about their # 24871 hitch and it fits just fine on versions of your 2012 Chrysler 200 that have dual exhaust tips so this hitch would work well for you.
I attached an install video for this hitch for you to check out as well. view full answer...
I have a hitch that is designed as a fit for your 2014 Chrysler 200, but the one you mentioned is not so it would not fit.
Instead you would want the part # C11133 which is a confirmed fit. view full answer...
I included an image for the instructions for Draw-Tite trailer hitch # 24919. As you can see the receiver will be basically the only part visible. This is because it is welded to the bottom of the cross tube which is hidden.
If you plan on doing some towing with the hitch on your 2015 Chrysler 200 then the correct ball mount to use is # 3593. For a 1-7/8 inch ball use # 19256 and for a 2 inch ball use # 19258. And for trailer wiring use # C56242.
If you want to use the hitch for an accessory... view full answer...
If you are looking for a good entry-level bike carrier the Thule Passage 3, # TH911XT is a good choice. This is a basic carrier with anti-sway cradles and it will secure to your 2015 Chrysler 200s using 6 straps.
The next step up is going to be the Gateway, # TH78VR, which has an upgraded style and design from the Passage. The Gateway Pro, # TH78VR, has the same basic design as the Gateway only it features upgraded cradles with road dampening technology, and an integrated cable lock.
But... view full answer...
The Swagman XTC-2 2-Bike Platform Rack part # S64670 is a great option for a 2013 Chrysler 200 Convertible when used with the Curt Trailer Hitch Receiver part # C11133. In regards to the convertible action, the bike rack should not interfere while folded flat with the upright laid down to the side. view full answer...
There is a trailer hitch receiver for your 2015 Chrysler 200, and for that I highly recommend the Draw-Tite Trailer Hitch Receiver # 24919.
This is the best option for your Chrysler because of Draw-Tite's reputation for quality and its easy installation. If you C56242, Draw-Tite Drawbar # 3593, and 1-7/8" Hitch Ball # 19256 or 2" Hitch Ball # 19258.
I have added a link to a video install for you to check out as well on a 2015 Chrysler 200 of the Draw-Tite Trailer Hitch Receiver # 24919. view full answer...
A padlock with a larger opening to accommodate the cables, like the Master Lock Padlock # ML4140LH will work to secure the 10-mm Braided Steel Cable # 72DPF. This lock is ideal for use with loop-end cables such as the # 72DPF. view full answer...
Go To Results