I spoke with my contact at K Source regarding the Extendable Panoramic Rearview Mirror, # KSRM012. He stated that it will fit over an On Star mirror on your 2001 Chevy Blazer. The only limitation will be limited access to one of the buttons on the right hand side of the mirror. It will still be accessible just not as accessible as if the mirror was not there. view full answer...
The Thule Apex you mentioned, part # TH9024XT is compatible with with either a 1-1/4 or a 2 inch receiver and would work very well on your Blazer, unless you have a rear mounted spare tire. If this is the case, take a look at the help article I have linked you to. The article shows how to check for clearance by measuring the distance from the hitch pin hole rearward to the rearward edge of the spare tire. The article shows the clearance measurements needed for many of our available bike... view full answer...
The hitch you will need for a 4 wheel drive 2000 Chevrolet Blazer is the Draw-Tite Class II hitch, part # 36244. This is a 1-1/4 inch hitch with a towing weight capacity of 3500lbs and a tongue weight capacity of 300lbs. When installing on a vehicle originally equipped with an OEM hitch, the OEM bumper brackets must be purchased and installed prior to a new hitch installation.
I am including links to the installation instructions of the Draw-Tite and a video of the hitch being installed... view full answer...
I do have a way for you to determine fit but I don't have any measurements of your 2002 Chevrolet Blazer so what you will need to do in order to confirm fit of the Derale 29" High-Output Electric Radiator Fan-and-Shroud Assembly part # D16928 is measure the space you have behind your radiator. This unit requires 28-5/8" wide x 13-7/8" tall x 3-1/4" deep of space to mount. If you have a clutch fan then you need to be especially careful of the depth measurement.
If you do not have space... view full answer...
We have not yet had the opportunity to install the Draw-Tite hitch # 75129 on a vehicle so I do not have a picture.
I have linked the instructions to the hitch on this page for your convenience. They will show up under the Featured Help Information bold writing.
I have also linked some Class III accessories that will work with your # 75129 hitch for you to check out. view full answer...
The Buyers Products Mud Flaps # 337B1018LSP are considered a universal fit and so long as you have enough room to mount them, they will fit on your 2019 Chevy Blazer. The mud flaps are 10" wide x 18" tall x 1/4" thick so you would need to ensure you have that much space to ensure they fit.
I have added a link to a video review for you to check out as well. view full answer...
Yes it will! Your 2020 Chevy Blazer does have the appropriate distance between the crossbars so you can mount the Thule kayak carrier, which is the following part:
- Thule The Stacker - Rooftop Multi-Kayak Carrier # TH830
This post-style kayak carrier will give you a really easy way to haul up to four kayaks at once on top of your 2020 Chevy Blazer. This carrier comes with enough straps for one kayak, so in order to carry a pair, you will also need more cinch straps and tie-downs:
-... view full answer...
You can use your Roadmaster Falcon 2 All-Terrain tow bar with the Blue Ox Base Plate Kit # BX1735 that fits your 2024 Chevy Blazer. In order to do this you need the Brackets Adapter # RM-031 which makes the connectors compatible with your base plate kit.
It doesn't look like Roadmaster has a base plate kit fit for your vehicle at this time (November 2023), but the Blue Ox solution will work just fine! view full answer...
I spoke with my contact at Curt and he stated that the trailer hitch # C13300 will fit your 2002 Chevy Blazer S-10 ZR2 model. I have included a link to the installation instructions for you to view.
If you plan on doing some towing, I recommend the etrailer ball mount kit # 989900 which comes with 2 ball mounts, 2 balls, a hitch pin with clip, and a carrying bag. For trailer wiring, use # 18252. I have included a link to a video that shows a typical installation of the wiring. view full answer...
The CIPA # 10201 custom fit towing mirror is not a confirmed match for your 2019 Chevrolet Blazer, however the CIPA # 7070-2 Universal Fit Towing Mirrors will fit and greatly improve your field of vision when towing. I use these on my Chevy Colorado and they are indispensable when passing on the highway and backing up. Best of all, you can move them to another vehicle as needed.
I have attached a video demonstrating the installation on a Blazer. view full answer...
The Clamp-On Adapters for Surco Safari Rack 5.0 Rooftop Cargo Basket # SP1101 are designed to install inside the tracks on the bottom of the Safari Rack 5.0 baskets. As long as your Safari Rack has the channel for the clamp-on adapter to slide into, the # SP1101 will work well for you.
The # SP1101 adapters will allow the Safari Rack 5.0 to attach to your Blazer's raised factory side rails. view full answer...
According to Roadmaster, the # 161-1 is the correct base plate kit for the 2001 S-10 Blazer 2 door, as long as it is a 2 wheel drive and not an Xtreme model. No base plate kits are available for 4WD or Xtreme 2 door models. The 161-1 is compatible with your tow bar.
According to step # 4 and 6 of the install instructions, at least two and maybe three holes will need to be drilled to install the base plate kit.
Because some vehicles will require modifications before they can be flat towed,... view full answer...
I checked with Draw-Tite and the Draw-Tite front mount hitch # 65004 fits the 1995 to 2005 Chevy Blazer, downsize, all models so that would include the ZR2s and 2 door models. I have included a link to the installation instructions for you to view. view full answer...
The Draw-Tite Front Mount Hitch Receiver, part # 65005, will fit the full-size Chevrolet Blazer for model years 1992 through 1994. It will not fit your 1989 Blazer. There is currently no front-mount hitch receiver available for your vehicle. I confirmed this with my technical contact at Draw-Tite.
We do offer a rear hitch receiver for your 1989 Blazer, the Draw-Tite Class III 2-Inch hitch, part # 75129. This rear hitch is rated for 500-lbs tongue weight, and is also rated for use with... view full answer...
Yes, the Blue Ox, # BX88272, is the correct fuse bypass switch for your 2000 Chevrolet Blazer which requires the RDO BATT (Radio/Battery) fuse to be pulled during flat towing. view full answer...
Yes, the Curt Trailer Hitch Receiver # C13418 is a confirmed fit for your 2021 Chevrolet Blazer RS model. This hitch has a bolt-on, no-drill installation and will provide you with a 2" receiver opening which is the most common size used for hitch mounted accessories such as bike racks, cargo carriers and ball mounts.
If you plan to do any towing you can add the T-One Vehicle Wiring Harness # 118720 which will provide a 4-way connector to power your trailers signal lights. If you don't... view full answer...
To attach a Pioneer tray to the roof of your 2022 Chevrolet Blazer I recommend using the Rhino-Rack Pioneer Platform Rack # RR46QX. This tray comes with its own fixed mounting points to attach directly to the flush mounted rails on your Blazer. Rhino-Rack does offer the Rhino-Rack Universal Pioneer Platform Rack # RR42115BF which you can mount directly to the Rhino-Rack Vortex Aero Roof Rack. This rack consists of the Crossbars # RRVA126B-2, Legs # RRRCL4 and Fit Kit # RR32SV. view full answer...
According to the Thule fit guide, their hatch mounted bike racks will not fit, due to the spare tire interfering. Instead they recommend using their spare tire mounted rack, the Thule Spare Me, part # TH963PRO.
Yakima offers a similar spare tire rack, the SpareRide, part # Y02599. Like the Thule rack, the SpareRide can also be locked to the spare tire and includes an integrated cable lock. view full answer...
Yes the Draw-Tite Max-Frame Trailer Hitch Receiver part # 75079 is a custom fit trailer hitch receiver confirmed to fit all models of the 2000 Chevrolet Blazer including vehicles equipped with the ZR2 package. It is a Class III trailer hitch with 2" receiver tube opening. I have attached a photo of what this trailer hitch will look like on a 2000 Chevrolet Blazer for you.
If you are looking to do any sort of towing you will need both a trailer wiring harness and a ball mount/hitch ball.... view full answer...