To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Extremely quiet, aerodynamic crossbars attach to Yakima towers to create a stylish roof rack for your vehicle. Rubber strips in T-slots push down to load carriers or accessories - no need to trim. Full-length aluminum bars maximize carrying capacity.
Features:
Yakima 60" JetStream MD - Silver:Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hi, everyone. Aiden here with Etrailer. Today, we're gonna be taking a look at and showing you how to install this Yakima JetStream roof rack system on our 2022 Ford Maverick. Now the JetStream crossbar is gonna be the main piece of our roof rack. That's the part that goes across the roof and serves as the attachment point for all of our accessories. Now this is an arrow bar, thicker in the front and tapering off towards the back with a T-track channel in the top if you take off your end caps.
The T-track up top will be for any sort of channel-mounted accessories. Just slide it in through this weather strip and to your place that you wanna mount it. It's nice because the weather strip is one solid piece, and it doesn't require trimming, but for the most part, people are probably gonna be doing clamp around accessories, which work great with this type of crossbar because you get a nice wide platform to mount it onto. It's not super thick, so you shouldn't need any adapters. And for most rooftop accessories out there, it's gonna work right out of the box.
The Ford Maverick has a naked roof, and what that means is that there's no pre-existing rails or crossbars on top. So we're gonna need a fit kit to make this work, and the kit does come with that. That's basically gonna be a set of rubber pads that fit around this lift on the side of the roof and custom length clamps that will actually go inside of the door jamb to secure the roof rack to the roof. Now every vehicle is going to have a different length clamp and set of pads, but these are the ones that work for our Maverick, and it gets a really strong hold on the roof. The pads fit excellent around here, and Yakima's roof racks have a ton of different adjustment points to make sure that everything is angled the proper way to ensure a strong fit on the roof, which I like a lot.
The install process sometimes gets a little bit of flack from people down here in the shop because it is more involved, but I do think it results in a better fit. The crossbars themselves are 60 inches long, which gives you plenty of room to mount up accessories and does have a little bit of overhang. Depending on the accessories you wanted to carry, you could even shift these crossbars offset a little ways if you wanted to maybe use something like a load assist kayak carrier, which would require a bit of overhang to make that work. And if that wasn't quite enough to make it work for your specific accessory, you could always pick up longer bars. Yakima's bars have a track underneath that runs the entire length, so you can pick up those longer bars and trust that it will work with your existing system.
Now, as far as some other measurements go, because these clamps and pads are custom fit for a certain spot from the Maverick, we can't move this around and the spread between the crossbars is going to be pretty fixed. And for us today, that's gonna be 33 inches. So for any sort of rooftop accessories, we need to note our crossbar spread. Depending on what we're putting up here, it'll work with a certain range of crossbar spreads. I'd say 33 inches is a really solid place to be, and it should work for most rooftop bike racks, boxes, cargo baskets, things like that. A roof rack will also add height to our vehicle. From the tallest point of the roof in the middle to the tallest point of the crossbar, it's gonna be four inches. And from that same point on the roof to the underside of the crossbar is three inches. So three inches of space underneath is plenty of room for any sort of clamp around accessories we might have. And then four inches added to the top isn't too bad. It sits well below our antenna here. So if we're just rocking the roof rack, we shouldn't have to worry about things like our garage or drive-throughs, parking garages, things like that. You will need to be mindful of it as we add other accessories on top of it, especially things like a box because that adds a lot of height to our vehicle, but the rack alone isn't too bad. It does support a weight capacity of 165 pounds. That's for the roof rack, not necessarily the roof on your Maverick. Be sure to check and make sure that you're not overloading the roof's weight capacity because oftentimes it is rated somewhat lower than the rack itself, but with all that in mind, just make sure you're not overloading it and haul things safely. And overall, I think a roof rack is a really helpful tool to have. The Maverick is obviously a smaller truck, and it does have its limitations. If you're looking to carry things like lumber, maybe some kayaks, or a ski and snowboard carrier or a box to get some extra space, a roof is a great place to put that, and I think with a truck like this, you see that we have a ladder rack on the back already, it can work really well in conjunction with something like that. If we're hauling two by fours and we have really long extended loads, then we can have it supported from the bed all the way up through the cab. But even with just the roof rack, I think it's gonna be a great way to carry things like kayaks and other longer equipment for those fun weekends out on the lake or at the trails. But the installation process is one of the places where I think this really shines. The Yakima roof racks, like I mentioned before, can be a little bit more involved, but on the Maverick, it's actually really straightforward. So we'll walk you through that whole process right now. Now a couple things before you start your install. The instructions are gonna have a lot of measurements in them because these Yakima roof racks have many points of adjustment. So be sure that you grab the instructions out of the base pad fit pit here. That's going to have all the measurements that pertain to your vehicle or in our case, our Ford Maverick today. And then the instructions will tell you where those measurements and those codes all apply. We'll walk you through the process too for the rear crossbar. Our front one's already installed, but just make sure you make note of all those different measurements. We're gonna start off with our feet. We're gonna pop the covers off just by squeezing the end and pulling it out. And then from the box that our crossbars come in, grab our adapter blocks, snap those into place on the top. You'll hear a small snap with that. And then the T-slot blocks. Pop that in the top middle, flip it upside down, and use the included tool to start threading that in. There's gonna be a small door right here where you can get that tool in, and don't fully tighten this down yet, just enough so it's just about level with these plastic blocks here. Now if that bolt underneath isn't exposed, you can see there's a small door right there. Yours might have just come undone or not, but if it's not available to see, just pull that clip back until you hear a click, and that will expose the bolt. We can then take our foot with that block in place and slide it into the underside of our crossbar, taking the end cap off, and getting that slid in on both sides, making sure that the block seats within that track well. Now if it doesn't want to go at first, you might have it misaligned, but it also just might be that you tightened it up too much. So you can loosen it up to get it to slide in a little bit easier if need be. And then when you're done, pop the end cap back on. Now it's gonna be really hard to see, but on the underside of the track, there's going to be markings with numbers. That's your measurement strip. Again, here in the shop it's probably really hard to see with the light, but that's going to be one of our first measurements we take. Your instructions will have an M1 and an M3 measurement. That's for the front and rear crossbar. So just get the base of your foot lined up with the appropriate measurement for your vehicle, and start to tighten it down in place using that first bolt that we used, but don't fully tighten it yet, just enough to keep it still. Once everything's in place, we need to set our pitch and our toe. Those are gonna be two more of the codes in your instructions labeled P1 and P2, and then T1 and T2. Those P codes are gonna be a letter A, B, or C and correspond to one of the dashes on the underside of your foot. And then same thing with the T code. That's gonna be a one, two, or three and correspond with its own set of dashes. So that P code is going to refer to the pitch of the tower. You can kind of see it moving back and forth right now. For our Maverick today, ours is B for both the front and the rear crossbar, which is nice and easy 'cause that just means it's centered up. We'll just fully tighten it down until our tool clicks. (tool clicks) And then for T, that's going to be this second bolt on the outside here. And if you loosen that up, that's gonna be for how our foot is oriented this way. Now, you'll wanna leave everything loose, but for us, we can just tighten it right down where it sits because it comes in the number two position, and that's just where we want to keep it. We can then take our base pads and clip them into the feet with the arrow on the bottom facing out. If the arrow's a little hard to see, you can just look for this notched cutout. That's gonna face towards the outside as well. With all this assembled, we can put it onto our roof now. Your kit in your instructions are gonna have another few measurements, M2 and M4. The M2 measurement is from the front end of your windshield to the first point where your clamp is gonna touch. And the M4 measurement is from the first crossbar to the second crossbar. Now I've gone ahead and since our first one's installed, measured it out, and put a piece of painter tape here as a way to mark out that spot, so I know where to set this. I've done it on both sides to also make sure that this is running parallel to our first crossbar, but I'll set this up in place, get the lip of our base clip here, and our base pad matching up with the roof here. And then we can open up our door and start installing our clamps on both sides. Now it's not quite flush with that ridge, but once we start tightening that clamp, it will pull it. So for now, what we're gonna do is push this first clip closed that we did at the very beginning and open up this second one here. And if you use painter tape, just pop that off and set it to the side. We can then take our clip and actually slide this in. There's a small slot under here where we can slide it in, and this bolt here will hook around it. And we'll notice that it's kind of sprung into place right now. There's two bolts we need to worry about tightening, the one where that clip is and the one up here a little bit higher. We're gonna start tightening that higher one first, and you'll notice that the clip starts to go down flat and sit against the side of the roof. Now as you're doing these, make sure you do them evenly on both sides. I've got the other one started first just a little bit here, and once it starts making contact, we can move to our other bolt, which will draw the clip up. Our goal here is to get the clip to sit as flush with the roof and that door jamb as possible. As we jump back and forth between tightening the two different sides, you'll get to a point where your tool will eventually start to click. That's when we know it's torqued down properly. We wanna make sure that that upper bolt is torqued down first on both sides. So once we hear that click, we'll know that that one's good to go. (tool clicks) And then I've already done the other side. We can do the same thing for this lower bolt for our clips, again, going back and forth evenly until they start to get properly torqued down. (tool clicks) And once you hear that click, you can close this plastic door here and pop our end caps back on. When the clips are in place, the door can close and the end cap will just hook in starting at the bottom and snap in at the top. If you chose to pick up optional lock cores, you could lock 'em up at this time, but right out of the box, they don't include them. So at that point, you're good to go. I'd like to give it a good shake test first just to make sure that nothing's shifting around either front to back or side to side. And we're good. So we're ready to hit the road. And that'll do it for our look at and installation of the Yakima JetStream roof rack system and seeing how it installs on our 2022 Ford Maverick. Thanks for watching.
Average Customer Rating: 4.8 out of 5 stars (64 Customer Reviews)
Extremely quiet, aerodynamic crossbars attach to Yakima towers to create a stylish roof rack for your vehicle. Rubber strips in T-slots push down to load carriers or accessories - no need to trim. Full-length aluminum bars maximize carrying capacity.Placed the order for the rack a year ago. I didn’t like the way it sat on the roof of my vehicle, but because I had already installed it, etrailer customer service refused to take it back. I would’ve gladly paid for the return shipping or some sort of restocking fee, but that wasn’t an option. I’ve had brand new rack and hardware sitting in their original boxes for a year.
Strong, Solid Bars, Super Light, and really easy to install!
My only complaint is the time it took to get my order. I understand this was out of your hands and dependent on supply problems.
Great secure product though some written instructions on their setup and installation would be helpful.
Of all of the many racks I’ve purchased over the years, this, by far, is the worst. Once installed, it is okay, but installing these towers is extremely frustrating. The front and back “clips” fall out requiring multiple attempts. When I contacted Yakima customer support, they acknowledged that they have received complaints about the product. Their solution was to just leave the racks on the car. I asked to be notified when a better product was available but a year later I’ve received no response. If this is the only option available for your vehicle (as it was for mine), then prepare to be frustrated. Otherwise, purchase a different product.
I bought both the roof rack and the cage from etrailer! Put everything on myself...easy peasy!
1 year later and still love my Yakima JetStream system. I've mostly used them to transport my kayak however I've also been able to transport some big box store items as well. They are very versatile. There is a t-track option as well as wrap around attachments. I've use ladder attachments, eyebolts, and Thule Hullavator in t-track. I've used Malone MegaWing and Yakima Skybox as wrap around attachment. What I really like about the t-track system is that you do not need to cut out the rubber track insert. You simply slide over the rubber, which allows you to adjust your system, on the fly, to load what you need to carry.
I needed crossbars for my new 2018 Mazda CX5, which came with flush side rails. The RidgeLine Towers for the Yakima crossbars, along with the vehicle specific kit worked great. The installation (10-15 min) is super easy. They look cool, and performed great (I strapped 160-lbs rooftop tent on them!). Removing them is also super easy (10 min tops). Highly recommend.
It's a great roof rack, but the paint is getting all scratched off...probably from sliding kayaks up onto it. I hope it doesn't rust. So far no signs of that.
I loved how easy these towers were to install. Took less than 30 mins total. They look nice and feel very sturdy. I am looking forward to loading the Kayaks up and getting out on the water next weekend.
Because of the 'rona-induced supply chain interruptions, I was unable to purchase all of my Yakima components from etrailer, but I did get these, and they are typically excellent Yakima components. Well-made, easy to install, good directions, no problems.
I chose the Yakima roof rack, because It spanned 50 inches, rather than the leading competitor's 47 inches, making it better for tying down 4 ft x 8 ft sheets of building material. It also seemed to be about half the price. It took me about 2 hours to put it all together and mount it on my car. The instructions were all visual and there was one little pic I didn't understand, but the equipment seemed to go together correctly anyway. Now that it's adjusted, it should be fairly easy to remove and replace next time. I did need to put on super tacky gloves to get the covers off. Although it seemed unnecessarily complicated, I would still choose this product again.
Easy installation. Great follow-up and service by etrailer post-delivery
Work exactly as they should and hold everything securely to my vehicle without interfering with the car’s normal operation. etrailer had best prices based on my research. These bars are much quieter than traditional round bars and worth the added expense.
Easy to install thanks to the etrailer video. I have used the rack system on many long distance trips including driving from South Carolina to Yellowstone.
Easy to install and sturdy. I carry a 9' pontoon boat on my camper shell using this rack at freeway speeds with no problems.
Happy with the purchase. Crossbars shipped and received quickly.
With exception of getting wrong towers (crossbar vs streamline), installation was fairly painless. Pay attention to measurements during install! Looking forward to the Yakima 16 to be fitted shortly and then ROAD-TRIPPING.
Yakima is always great, the bars are just right for my kayaks and look great too.
Everything arrived in a timely fashion and the instructions were simple to follow. The fit is good and look forward to many years of use. Kayaks are awaiting for racks to arrive. Thanks for a great product
The racks fit well and secure on 2021 Palisade. A little cumbersome to assemble but a little patients goes a long way. Also 4 pieces were robbed from one box.
The people at etrailer made it right by sending the lost part ASAP.
Thank you
Received this Yakima roof rack system for my flush-rail 2019 Mazda CX-5 Signature on Thursday, and installed it on Friday.
It’s not the simplest installation I’ve encountered, and I’d had a number of Thule products before. I found the installation “picto-grams” not that helpful. Also the 3.5 newton-meter torque screwdriver provide would not “click”.
It looks great on the Mazda, but took about 4 hours to install - getting the clips in place was an issue ; I got the outer to clip on, only to find the inner had come off its attachment clips- very frustrating.
really good product instructions could be a little better.
Prompt delivery. Delivered exactly what was ordered. No hassle.
No complaints. Except I wish we used it more. Everything went well, their assistance in selection was great and the install went flawlessly.
Do you have a question about this Roof Rack?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.