Off-road LED light bar shines a mixed spot/flood beam so you can see the trail at night or in bad weather. Installs on your roof, roll bar, bumper, or grille guard with included adjustable brackets and wiring harness.
Features:
Specs:
Videos are provided as a guide only. Refer to manufacturer installation instructions and specs for complete information.
Hello everybody. This is Jeff at etrailer.com. Today we're gonna take a look at the Arc Xtreme 20 inch long LED mixed beam light bar kit. Now this offroad LED light bar will shine a nice bright white mixed spot and flood beam so that you can see the trail at night or in bad weather. That combo beam increases the visibility in front of you. And then off to both sides.
Now the beam distance, the spot beam will go 1,837 feet distance. The flood beam will go widthwise. So 203 feet wide in the flood beam pattern. This does offer 40 LEDs which will provide 10,400 lumens of light. And I do have, this comes with the wiring harness.
I do have this wiring harness hooked up with some 12 volt power just to show you how bright the light is. So what I'm gonna do is it has this rocker switch here. It's a lighted rocker switch that when you do turn it on you can see just by turning this on you can see the light comes on and actually the rocker switch lights up. I'm gonna go ahead and turn off the overhead lights and you can see how bright it is. And again, it's a very bright white light.
It's 40 LEDs. And again, you got your toggle switch or your rocker switch here that you can just turn off. And then again, turn it back on. You can see the red light shows you the switch is operating and then your light comes on. And turn back on our overhead lights.
We'll go ahead and turn off our light. And zoom in, talk about the light itself. It is a durable polycarbonate lens which is impact and shatter resistant. You can see the housing is a black powder coated aluminum housing, resists corrosion. Has an IP 67 rating to protect against dust and moisture. And to install this it's a very simple installation to your roof, your Rollbar, your grill guard, or your bumper. It will include the mounting hardware and we've actually attached both brackets that comes with the side brackets. And then you can see the bottom mounting brackets. You can use both of 'em or you can use either one if you prefer. Gives you different installation options, comes with the mounting hardware to install it. Now, this is a 20 inch length light. It is also available in a 30 inch length. We do sell that separately on our website. These mounting brackets once you install 'em, they are adjustable. So you can actually turn it and let you change the angle of the light as needed. Now, the wiring harness over here we mentioned, I am gonna unplug it here and I'm gonna detach it from the 12 volt power. So we can talk about the wiring harness itself. You can see here's your wiring harness. It does come with the rocker switch I had showed you earlier. There's your rocker switch right here. It makes you turning it on and off. It is lighted to let you know if it's on or off. And it could just by switching it and turn it on or off. Does include this triple sealed Deutsch DT connector that you can see is what'll plug right into your light, locks into place. Push down to unhook it. Comes with a relay right here. It's an HID relay. And then the lead wires right here to connect to your battery, has the ring terminals on it and it comes with a fuse. So it is fuse protected. Now this light is intended for offroad use only. It does not meet the DOT or SAE standards. Zoom back out here, a few specs on this. It is for quantity of one light bar. The lumens again is 10,400 lumens. Total LEDs is 40 LEDs and it's six Watts per LED. So that's 240 Watts at 13.6 volts DC. And the last thing I'm gonna do is just give you the dimensions on this. Zoom back in on that. The overall length from one end to the other is gonna be right at 22 inches for the length. Total depth on the light is only about two inches deep and the total height. I just wanna measure the light bar height, not including the mounting brackets. So it's about two and 13 16ths of an inch tall, just under three inches. And if I go down to we're including the mounting brackets to the very top, it's about three and a half inches tall. But that should do it for the review on this Arc Xtreme 20 inch long LED mixed beam light bar..
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.