Summer Starts Here - Save up to 70%
To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
The chrome-plated ball on this gooseneck hitch locks in place with 2 pins for extra security. When you're done towing, flip the ball over and store it inside the hitch, freeing up your truck bed. Innovative center locator eases installation.
Features:
Specs:
The Curt EZr Double Lock underbed gooseneck trailer hitch provides a sturdy, secure connection for towing your gooseneck trailer and also allows for a clean, unobtrusive look for your truck bed when you aren't towing. To tow, simply pull the included handle out to unlock the hitch. Then insert the chrome-plated hitch ball into the ball hole. You may need to rotate the ball to line it up with the dual locking pins. When the ball drops into place, rotate the handle counterclockwise until the locking pins snap into position. Because there are 2 locking pins instead of 1, you get extra security for your towing setup.
Get full bed access when you're not towing. Just remove the ball, flip it upside down, drop it back into the ball hole of the hitch, and use the handle to lock the ball in place. A rubber cover is included with the EZr Double Lock. When the ball is stowed upside down in the hitch, place this cover over the ball hole to keep out dirt and grime and create a clean look for your vehicle.
The innovative center locator tool included with this gooseneck trailer hitch is designed to make installation fast and easy by eliminating the need to measure where the ball hole must be cut into your truck bed. Once you have the custom installation kit in place and the gooseneck hitch is properly attached to the rails, the bright orange locator will help you to finish installation.
Use the hole at the center of the locator to line up your 3/16" drill bit, and drill up from beneath the bed to create a pilot hole. This pilot hole will be your guide as you cut the 4" diameter ball hole into your truck bed.
When you begin cutting through your bed, the locator will act as a trim shield, ensuring that you don't drill too deep. Continue cutting from the top of your truck bed until orange shavings appear. Once you see these shavings, you've gone far enough. The center locator can be easily removed from the hitch once installation is complete.
Alternate Instructions
Tech Tip
On models with plastic wheel well covers, they may need to be temporarily removed if they interfere with installation. No drilling required to install the frame brackets of installation kit. Installation rails are rated to meet vehicle manufacturer's tow ratings - see vehicle owner's manual
Average Customer Rating: 4.5 out of 5 stars (100 Customer Reviews)
The chrome-plated ball on this gooseneck hitch locks in place with 2 pins for extra security. When you're done towing, flip the ball over and store it inside the hitch, freeing up your truck bed. Innovative center locator eases installation.Seems to be very well built. Shipping was very fast. Will definitely purchase other products.
Great hitch and easy to use. I did have to lift up the bed a little bit to install it. Took me about 5 hours because of that but otherwise it is a great hitch. The rings for the safety chains stay on the bed and the ball flips over and stows away completely.
shipping lost a box Men when box arrived 17 was destroed and missing parts. Need to do better job of packing for Shipping. Still waiting for missing parts.
The hitch works fine and was easy to install. Everything fit well with one exception. The rod that locks the ball in place from the wheel well is too short. I expect it is the wrong rod for the 2013 Ram pickup. I made an attempt to contact etrailer to get another, but failed to contact anyone. Can you put me in contact with someone who can assist me in getting a replacement?
I've had it over a year now installed it myself without any help, I think it was very easy to install.
I tow everything with it never had any issues.
GREAT Service. Received a phone call on the same day as the order to confirm the order. Even down to where it was to be left. Several e-mails letting me know the progress. Received it in 3 days after the order. One day was Sunday so i guess it doesn't count. All the parts are there. I do have an issue with UPS. The instructions on the label says LOT # 2 Montana. They left it at the entry house instead. Having a dislocated arm and loading and unloading was not good. They need to work on that. Yes the camper can be easily seen from the house. Can't wait to get it in.
Thanks
Daniel J.
2/28/2019
Installation was great and easy. Has performed as advertised
Overall a decent product. Easy to install, hardest part was manhandling all the pieces by myself. Tows wonderfully.
The only negative is the length of the ball when in stored position. I have 2004 Dodge Ram 3500 2wd that sits low to the ground. When stored, the ball strikes the top of the axle housing and cut the ABS wiring. Easy repair and we no longer store the ball in the hitch
I have a turnover gooseneck ball hitch used for pulling a 32 foot stock trailer. I have no complaints, took me and a friend about 2 hours to install. Had a $75 mailin rebate so was significantly less than a B&W hitch.
The install of this hitch was great. Fit fine and works as it should. Only issue I had was that I'm the second owner of the truck and first owner had installed both a gooseneck and a 5th wheel hitch and welded a bunch of brackets to the truck frame, then removed both hitches before he got rid of truck. I had to spend a couple hours grinding the brackets off before I could install new hitch. I had to inlarge hole for the gooseneck ball as the placement of new ball was 2.5"s farther back then the original hitch that had bee there previously.
The hitch was received in a very timely matter, ordered then three days it arrived. FAST! I didn't install immediately.... about three days went by... After work I tried to read the so call instructions and started assembly... start time 3:30 pm end time 8:30pm had all but the latch and rod handle and springs to install. I did that the next day. Bolting the receiver part under the bed was definitely a TWO PERSON job or at least with some kind of blocking or jack may be used... As far as the total receiver bolting and receiver installation, *follow the instruction* it's really laymans terms and pics help tremendously! It does get very frustrating putting the ball pin rod in the ball pin... If I may suggest, in your companies instruction advising to inform the installer to use needle nose locking pliers to clamp the spring back in front of the 3/8" washer on the hitch rod WHILE installing the small little bolt into the hitch pins! This way, It gives the installer adequate adjustment to have to install the hitch rod and pins since one can hardly see the hole if they are aligned or not.
Other than that little difficult issue, It was pretty smooth and easy... (just alot of struggling and dirt) if you don't mind...
Very pleased with this product!!
Missing hardware took 2 weeks to get new hardware and it was the wrong hardware so I had to go spend extra money and aggravation to buy my own hardware that should have came in the kit
Brooke M.
8/13/2021
Thank you for your review! Our Customer Service team will be reaching out to you!
installation took us about 4.5 hours total on Dodge Ram 2500 2006. removed both wheel well covers, and wheel tire assembly to get torque wrench on large bolts. why the big spacers, leave little bolt in nut contact? Product seems solid...
This hitch was an easy install, only a couple of hours and no welding or bed removal. I would like to thank Gwen, my sales rep, for her great customer service and when I explained I was on a time crunch to get the hitch she assured me that would not be an issue. Sure enough I received the hitch in just a couple of days.
Fairly easy to install. Instructions were a little difficult to follow but the diagram of the hitch and how it goes together made it easier. The company was very easy to work with. I would recommend this product and company to anyone!
Good quality, heavy made hitch. It took me about 4 hours to install and that was taking my time and looking over instructions repeatedly.
Easy to put in and after a year I’ve had no issues.
I am happy with this hitch.
Robert M.
2/13/2021
It has served me well.
Great customer service and great product. I’d definitely recommend to anyone looking
Haven’t had a chance, but to bring the box inside. It was pretty torn up started to check the box for missing parts.
But the speed for delivery was great. The product look to be undamaged.
Works flawlessly.
Great job shipping very fast will continue to buy from thank you for easy ordering looks like a great product will sends pic when I get it on the truck
Excellent customer service and supper fast shipping
Do you have a question about this Gooseneck Hitch?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Heather A.
2/25/2019
I contacted Curt and they wanted to make sure you did not install the handle facing up and it is hitting the inner fender. The handle should be down on these.