To see if this custom-fit item will work for you please tell us what vehicle you'll use it with.
Thank you! Your comment has been submitted successfully. You should be able to view your question/comment here within a few days.
Error submitting comment. Please try again momentarily.
Quickly and easily install a 4-way trailer connector on your vehicle with this custom harness. T-connector plugs directly into existing wiring. Powered converter reduces strain on wiring system and is made using SMT to ensure superior performance.
Features:
Specs:
Installation
This custom-fit T-connector plugs into your vehicle's wiring harness, which is located behind the driver's-side and passenger's-side tail lights. You will have to remove the tail light assemblies to access this harness. Once you've plugged in the T-connector, run the hot lead up to your car battery. Connect the lead to the included fuse holder, and then connect the fuse holder to the positive terminal on your battery.
Once installation is complete, the 4-way connector will be stowed in an out-of-the-way location within your cargo area.
It is recommended that you use a small amount of grease on all electrical connections - the plugs on your automobile and the 4-pole connector itself - to help prevent corrosion.
A tail light converter is built into this T-connector. This converter is a circuit-protected, battery-powered unit that bypasses the electrical routes that are used by a basic wiring harness. As a result, there is virtually no draw on your tail light circuits.
Because most trailers run on a two-wire system - wherein the brake and turn signals are carried on one wire - the separate brake and turn signals from your vehicle's three-wire system need to be combined so they are compatible with the wiring system of the trailer. This converter combines the brake and turn signal functions of your automobile so that they run on one wire to properly activate your trailer's tail lights. Note: This will not affect how the tail lights on your vehicle operate.
Curt builds each tail light converter using surface-mount technology (SMT). This method of construction involves soldering electronic components directly to the surface of a printed circuit board. SMT eliminates the need for leads, which are used in older through-hole technology. The result is a circuit board that is smaller yet provides more routing area and that offers superior performance, reliability and durability.
Circuit boards constructed using SMT have been shown to perform better under rough conditions with excessive vibration than those made using the through-hole method. And where would vibration be more likely to occur than in towing applications? Curt converters also produce less heat, leading to increased durability and longer life. In addition, lower levels of resistance ensure better performance, especially for parts that operate at higher frequencies.
Each Curt circuit board is made using high-quality components that are pieced together in the most technologically savvy fashion, leading to greater predictability and reliability in functioning.
Average Customer Rating: 4.9 out of 5 stars (25 Customer Reviews)
Quickly and easily install a 4-way trailer connector on your vehicle with this custom harness. T-connector plugs directly into existing wiring. Powered converter reduces strain on wiring system and is made using SMT to ensure superior performance.Installed yesterday. Only issue with the install on our 22 Maverick Lariat was how to route the power lead to the battery in the engine compartment. Finally removed drivers side fasteners holding the fiber mat that encloses the entire underside and routed the wire behind the tail light, above the mat and then fished it into the engine compartment from behind the front wheel well. Everything seems to work fine so far, but a more complex install than anticipated due to fiber mat. Love the fact that no wires had to be cut/spliced and harness is completely isolated from vehicle electrical system.
Ford installed my shell but could not wire third brake light. It has a 4pin but if I used that, it turned off the blindspot sensors. I found this at E-Trailer. It worked perfectly. I didn't need the trailer parts and just used the jumper/pigtails.
great product. literally plug and play. clear instructions and great youtube video. perfect fit for my 2022 ford maverick.
Everything lined up perfectly. Solid product and the wiring harness was perfect.
It worked exactly like it was advertised. I could not find at Ford but I found it here at etrailer. Very informative people to talk to and WANT To Help, I've found this to be the case with other products purchased from etrailer. (ETAILER Company)You have a great staff, keep doing what you are doing and you will continue to be Successful.
Installed easily!
The hitch and wiring were great
Easy to install
Fantastic service quality products !
Proper wire kit made custom for my truck
Good installation directions @ good quality products
Great product description. Quick shipping. Great tracking information
Fast and accurate
Fast shipping.works as it should.
Do you have a question about this Custom Fit Vehicle Wiring?
Info for this part was:
At etrailer.com we provide the best information available about the products we sell. We take the quality of our information seriously so that you can get the right part the first time. Let us know if anything is missing or if you have any questions.
Jim
12/9/2023
Working perfectly after 1 year.